rtd BDM-610000049 Скачать руководство пользователя страница 96

Страница: 96 / 120

CMX158886 cpuModule

BDM-610000049

Rev G

Jumper Settings and Locations

Many cpuModule options are configured by positioning jumpers. Jumpers are labeled on the board as

followed by a number.

Some jumpers have three pins, allowing three settings:

•

Pins 1 and 2 connected (indicated as “1–2”)

•

Pins 2 and 3 connected (indicated as “2–3”)

•

No pins connected

Some jumpers have two pins, allowing two settings:

•

Pins 1 and 2 connected (indicated as “closed”)

•

Pins 1 and 2 unconnected (indicated as “open”)

Figure 7 shows the jumper locations that are used to configure the cpuModule. Table 62 lists the jumpers and
their settings.

JP9

JP2

JP13

JP6

JP14

JP5

JP1

JP12

JP11

Содержание BDM-610000049

























































































































Результаты поиска

Содержание BDM-610000049

Отзывы:

Похожие инструкции для BDM-610000049

Бренды по названию

Популярные бренды

rtd BDM-610000049, Руководство пользователя

Результаты поиска

Содержание BDM-610000049

Отзывы:

Похожие инструкции для BDM-610000049

Бренды по названию

Популярные бренды