rtd BDM-610000049 Скачать руководство пользователя страница 46

Страница: 46 / 120

CMX158886 cpuModule

BDM-610000049

Rev G

Save the settings in the BIOS setup

Remove power from the system.

Insert the Disk Chip in the ATA/IDE Disk Chip Socket (

U16

) aligning pin 1 with the square solder pad

on the board.

Apply power to the system.

Re-enter the BIOS and set the boot order of the system accordingly.

Figure 5

CMX158886 before and after ATA/IDE Disk Chip Installation

WARNING

The preceding steps should be performed before installing the Disk Chip in the ATA/IDE Disk

Chip Socket. These steps ensure that the system is properly configured for the correct device and supply
voltage, so neither the Disk Chip or cpuModule are damaged.

ATA/IDE Disk Chip Socket (U16)

Pin 1 indicated by arrow

ATA/IDE Disk Chip

Pin 1 indicated by arrow

Содержание BDM-610000049

























































































































Результаты поиска

Содержание BDM-610000049

Отзывы:

Похожие инструкции для BDM-610000049

Бренды по названию

Популярные бренды

rtd BDM-610000049, Руководство пользователя

Результаты поиска

Содержание BDM-610000049

Отзывы:

Похожие инструкции для BDM-610000049

Бренды по названию

Популярные бренды