rtd BDM-610000049 Скачать руководство пользователя страница 32

Страница: 32 / 120

CMX158886 cpuModule

BDM-610000049

Rev G

Booting the CMX158886 cpuModule for the First Time

You can now apply power to the cpuModule. You will see:

•

A greeting message from the VGA BIOS (if the VGA BIOS has a sign-on message)

•

The cpuModule BIOS version information

•

A message requesting you press

Delete

to enter the Setup program

If you don’t press

Delete

, the cpuModule will try to boot from the current settings. If you press

Delete

, the

cpuModule will enter Setup. Once you have configured the cpuModule using Setup, save your changes and
reboot.

Note

You may miss the initial sign-on messages if your monitor takes a while to power on.

Note

By default, cpuModules are shipped with Fail Safe Boot ROM enabled. When Fail Safe Boot ROM

is enabled, the system will boot to it exclusively.

Содержание BDM-610000049

























































































































Результаты поиска

Содержание BDM-610000049

Отзывы:

Похожие инструкции для BDM-610000049

Бренды по названию

Популярные бренды

rtd BDM-610000049, Руководство пользователя

Результаты поиска

Содержание BDM-610000049

Отзывы:

Похожие инструкции для BDM-610000049

Бренды по названию

Популярные бренды