rtd BDM-610000049 Скачать руководство пользователя страница 16

Страница: 16 / 120

CMX158886 cpuModule

BDM-610000049

Rev G

Cable Kits and Accessories

For maximum flexibility, RTD does not provide cables with the cpuModule. You may wish to purchase the
CMX158886 cpuModule cable kit (P/N XK-CM65), which contains:

•

Multi-function utility harness (keyboard socket, battery, reset, speaker)

•

Two serial port cables (DIL-10 to DSUB-9)

•

Parallel port cable (DIL-26 to DSUB-25)

•

Two IDE cables

•

VGA monitor cable (DIL-10 to high density 15-pin DSUB)

•

Power cable (DIL-12 to wire leads)

•

Two USB cables (5-pin SIL to USB A)

•

Audio Cable (DIL-10 to three Mini-Jacks)

•

One Ethernet cable (DIL-10 to RJ-45)

A floppy drive cable kit (P/N XK-CM49) is also available for connecting to the multiPort. This cable kit comes
with:

•

3.5” HDD Floppy Drive with a multiPort interface board

•

Two floppy cables

For additional accessories, refer to the RTD website.

Содержание BDM-610000049

























































































































Результаты поиска

Содержание BDM-610000049

Отзывы:

Похожие инструкции для BDM-610000049

Бренды по названию

Популярные бренды

rtd BDM-610000049, Руководство пользователя

Результаты поиска

Содержание BDM-610000049

Отзывы:

Похожие инструкции для BDM-610000049

Бренды по названию

Популярные бренды