RTA 460EC-NNA4 Скачать руководство пользователя | Manualshive

Страница: 11 / 59

background image

Real Time Automation, Inc.

11

1-800-249-1612

Accessing the Main Page

The following steps will help you access the browser based configuration of the gateway. By default,
DHCP is enabled. If the gateway fails to obtain an IP address over DHCP it will Auto IP with 169.254.X.Y.
For more information on your Operating system network setting refer to the Access Browser
Configuration Doc on the CD or download from our support web site.

1)

Insert the provided CD-ROM into a computer also on the network.

2)

Run the IPSetup.exe program from the CD-ROM.

3)

Find unit under “Select a Unit”.

a.

Change

Gateway’s

IP address to match that of your PC if DHCP has failed.

i.

You will know DHCP has failed if the gateway’s IP address is AutoIP at 169.254.X.Y.

ii.

If successful, it will say DHCP’d at ex: 192.168.0.100 or however your DCHP Client is set up.

b.

If you do not see the gateway in this tool, then your PC is most likely set up as a static IP.

i.

C

hange your PC’

s network settings to be DHCP. If DHCP fails, then it will change to be on the

169.254.x.y network.

ii.

Relaunch the IP Setup tool to see if gateway can be discovered now.

4)

Click

Launch Webpage

. The Main page should appear.

Default setting is set to DHCP. If DHCP fails, default IP Address is 169.254.x.y

«
...
9
10
11
12
13
...
»

Содержание 460EC-NNA4




























































Отзывы:

Нет отзывов

Похожие инструкции для 460EC-NNA4

Бренд: NetComm Страницы: 16

Бренд: Media5 Страницы: 54

Бренд: Pace Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Nitgen Страницы: 66

Бренд: Arris Страницы: 2

CONNECT RETH001

Бренд: CAME Страницы: 32

Бренд: VOGO Страницы: 24

Бренд: ATX Страницы: 84

CG-ARM7/GTI HS/LS

Бренд: EMS Страницы: 22

Бренд: EMS Страницы: 22

Бренд: Planet Страницы: 62

Бренд: Lantronix Страницы: 2

Бренд: BellEquip Страницы: 20

RINT8CH Wireless Gateway

Бренд: Rintech Страницы: 2

Бренд: sauter Страницы: 26

Бренд: Technicolor Страницы: 106

Бренд: Hybertone Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды