WCS-7100 Radio Programmer Help
142
© 2021 RT Systems, Inc.
Set to 0 seconds to resume immediately upon the loss of a signal (remember,
this could cause scanning to resume just because someone pauses in a
conversation;
1-5 seconds which causes scanning to resume when the signal is lost for the
selected period of time, or
Hold which causes scanning to halt even after the signal is lost.
dF Span- Set the dF Span (Delta Frequency) value from the drop-down menu.
Delta frequency scanning searches for signals within the specified range with the
displayed VFO frequency or Memory channel frequency as the center frequency.
The frequency range is specified by the width of the selected span.
Program Scan Edge- Select the desired group from the Program Scan Edge.
Memory Scan- Select the desired memory scan function value.
Memory - All memory channels are scanned.
Select - Only memory channels marked as Select Scan are included. A
channel is marked as Select Scan as one of the options for each memory
channel.
Mode - Scan channels on the same operating mode as the one currently
displayed.
Scan Resume- Check to engage Scan Resume
Checked - When a signal is detected, the scan pauses for 10
seconds, then resumes whether or not the signal is lost. If the signal
does not last for 10 seconds, scanning resumes 2 seconds after the
signal disappears.
Unchecked - When a signal is detected, scanning ceases. It must be
started again manually if desired.
TX
Delay - Tx delay sets the timing of the transmission for each operating band. Why
you might need this: When an external device, such as a vacuum tube linear
amplifier or a receiver preamplifier, is connected to the transceiver and you use the
SEND line, a problem could occur if the transmit/receive switch of the device is
slower than that for the Icom transceiver. The RF power could damage the device
that is not yet ready. The TX delays help prevent that damage.
Содержание WCS-7100
