background image

 

M0619-1 ver 2.6 

 

7  

1.1 Safety 

1.1.1 General 

The integrator installing the tool changer into the system must follow the safety demands stated 
in standards and provisions applicable in the country where the tool changer system is to be 
installed. The products are all prepared for CE-certification. 

The user of the Robot System Products tool changer is responsible that law and directives 
applicable in respective countries, with regards to safety, are followed. The user is also 
responsible to guarantee that all safety devices are installed correctly. 

WARNING! 

Never carry out service work on a robot that has not been taken out of operation. 
See safety information for the robot.

 

WARNING! 

Only perform work on grippers or tools attached to the tool changer if the air 
pressure is safely switched off.

  

WARNING! 

Be aware that tool changer and tool attachment are heavy and may cause 
personal injury and equipment damage if dropped.  

NOTE! 

The tool changer shall always be in locked position, also when empty, to avoid 
unexpected locking if air pressure is lost. 

 

1.1.2 Explanation of warnings 

The warnings in this document are specific to the products in this manual. It is expected that the 
user also pay attention to certain notifications from the robot manufacturer and/or the 
manufacturers of other components used in the installation. 

WARNING! 

The warning sign will make you aware that a situation could result in potential 
serious injury or damage to equipment. 

NOTE! 

The note sign will alert you about something important to consider. 

Содержание P6411











































Отзывы: