Put cleaner into an upright
position. Remove the two (2)
screws located on either side
of the headlight lens.
1.
Pull bulb out of socket to
remove. Do NOT twist. Push
bulb into socket to replace.
2.
Secure the headlight lens by
replacing the two (2)
screws.
3.
TOOL REQUIRED: FLATHEAD SCREWDRIVER
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK - UNPLUG CLEANER BEFORE REMOVING OR REPLACING LIGHTBULB.
LIGHTBULB: REMOVAL & REPLACEMENT
This cleaner uses a common automotive lamp #906, 13.0 volts. For bulb replacement call 1-800-321-1134
or your local auto parts store.
11
12
ANY OTHER SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE
CUSTOMER SERVICE (1-800-321-1134)
In the event that further assistance is required, see your Yellow Pages for an authorized Royal
®
Dealer. Costs of any
transportation to and from any place of repair are to be paid by the owner. The service parts used in this unit are
easily replaced and readily available from an authorized Royal
®
Dealer or retailer. Always identify your cleaner by
the model number and manufacturing code when requesting information or ordering replacement parts. (The model
number appears on the bottom of the cleaner.)
WARNING:
TO REDUCE RISK OF PERSONAL INJURY - UNPLUG CLEANER BEFORE SERVICING
POSSIBLE REASON
POSSIBLE SOLUTION
TROUBLESHOOTING GUIDE
Cleaner won’t run
Cleaner won’t
pick-up or low
suction
Dust escaping
from cleaner
Cleaner tools
won’t pick-up
Headlight not
working
Cleaner is difficult
to push
Brushroll not
rotating
Belt burns or
breaks
PROBLEM
1. Power cord not firmly plugged into
outlet.
2. Blown fuse or tripped breaker.
3. Needs service.
1. Paper bag full.
2. Paper bag not installed correctly.
3. Broken or worn belt.
4. Carpet height setting is incorrect.
5. Unit misassembled resulting in air
flow leakage.
6. Dirty HEPA filter.
7. Brushroll worn.
8. Dirty bag chamber filter.
1. Paper bag full.
2. Paper bag not installed correctly.
3. Puncture/hole in paper bag.
4. No bag in cleaner.
5. Dirty bag chamber filter.
1. Hose clogged.
2. Bag inlet clogged.
3. Paper bag full.
4. No bag in cleaner, filter clogged.
1. Bulb burnt out.
2. Loose electrical wires.
1. Carpet height setting is incorrect.
1. Broken belt.
2. Brushroll jammed with an
obstruction.
1. Brush may be jammed with debris.
2. Brush end caps are clooged with
debris.
3. Carpet height setting is incorrect.
1. Plug cord in firmly.
2. Check fuse or breaker in home. Replace
fuse/reset breaker.
3. Take to service center or call 1-800-321-1134.
1. Replace paper bag - Pg. 8
2. Insert finger into hole and push paper away
from opening OR review paper bag removal and
replacement - Pg. 8.
3. Review belt removal and replacement - Pg. 9, 10.
4. Set carpet height adjustment to appropriate
setting for carpet being cleaned - Pg. 7.
5. Reassemble unit / review assembly - Pg. 6.
6. Replace HEPA filter - Pg. 8, 9.
7. Review brushroll removal and replacement - Pg. 9, 10.
8. Review general maintenance - Pg. 10.
1. Replace paper bag - Pg. 8.
2. Review paper bag installation - Pg. 8.
3. Replace paper bag-Pg. 8. Clean/replace filters -
Pg. 8, 9.
4. Install bag & clean filter - Pg. 8, 9.
5. Review general maintenance - Pg. 10.
1. Remove hose and tools; remove obstruction - Pg. 7.
2. Remove hose (Pg. 7) and paper bag (Pg. 8).
3. Replace paper bag - Pg. 8.
4. Install paper bag (Pg. 8) and clean filter (Pg. 8, 9).
1. Replace bulb - Pg. 11.
2. Call 1-800-321-1134 for nearest authorized
Royal
®
Dealer.
1. Set carpet height adjust lever to appropriate
setting for carpet being cleaned - Pg. 7.
1. Review belt removal and replacement - Pg. 9, 10.
2. Turn the unit off and unplug. Remove the
obstruction. Plug unit back into outlet and turn
the power to the “on” position.
1. Remove brushroll - Pg. 9, 10. Clean brush of debris.
2. Remove brushroll. Determine if end caps
rotate freely. If not, replace brushroll - Pg. 9, 10.
3. Set capet height adjustment to appropriate
setting for carpet being cleaned - Pg. 7.
