Ri 6230-01
October 10, 2000
Page 5
Ri 6230 Machine Specifications
Type
Console
Copying system
Dry, indirect electrostatic system
Originals
Sheets and books
Maximum size: 11" x 17"
Original feed system
Fixed
Copy paper
Cassette and duplex unit: Plain paper 16~24lb. Bond
Bypass table: Plain paper 16~43lb. Bond (43lb. Bond = 90lb. Index)
Special paper: Transparencies, tracing paper, colored paper, letterhead,
and envelopes (only when used as a printer) Note: Use the bypass table for special paper.
Copying sizes
Maximum: 11" x 17"
Minimum: 5 1/2" x 8 1/2"
During duplex copying:
Maximum: 11" x 17"
Minimum: 5 1/2" x 8 1/2"
Magnification ratios
Manual mode: 25 – 400%, 1% increments
Auto copy mode: Fixed ratios
1:1, 1:4.00/1:2.00/1:1.29/1:1.21/1:0.78/
1:0.64/1:0.50/1:0.25
100% magnification
Copier:
±
0.8%
SRDF:
±
1.5%
Enlargement/reduction
Copier:
±
1.0%
SRDF:
±
1.5%
Copy speed
At 100% magnification in memory copy mode:
11" x 8 1/2", 62 copies/min.
8 1/2" x 11R", 44 copies/min.
11" x 17", 32 copies/min.
8 1/2" x 14", 38 copies/min.
When the SRDF is used at 100% magnification
11" x 8 1/2": 62 copies/min.
First copy time
3.6 sec. or less 11" x 8 1/2", 100% magnification,
Upper drawer, manual copy density control.
Warm-up time
360 sec. or less (room temperature 68°F/20°C, 65%RH).
Paper feed system
Automatic feed.
Capacity: Two Cassettes: 550 sheets.
Large Paper Deck: 3000 sheets.
Manual feed
Capacity:
Bypass: 100 sheets.
Photoconductor
a-Si (film thickness 30
µ
m, drum diameter 84 mm).
Charging system
Single positive corona charging, 900
µ
A.
Exposure light source
Semiconductor laser.
Developing system
Dry, reverse developing (double magnetic roller).Developer: 2-component, ferrite carrier and N32T black toner.
Density control: Developer density detection. Toner replenishing: automatic from a toner hopper.
Transfer system
Transfer belt, approximately 1.2 to 1.3 kV, (rated current: 50
m
A.
Separation system
Transfer belt and separation claws.
Fixing system
Heat roller: Heat source: halogen heaters (main 970 W, sub 270 W). Control temperature:
356°F/185°C (at normal ambient temperature). Abnormally high temperature protection
devices: 356°F/180°C thermostats.
Charge erasing system
Exposure by cleaning lamp.
Cleaning system
Cleaning blade.
Scanning system
Flat bed scanning by CCD image sensor.
Bit map memory
64 MB (standard).
Image storage memory
8.5 GB (standard).
Resolution
600 x 600 dpi.
Light source
Inert gas lamp (24W).
Dimensions
26 15/16" (W) x 31 5/16" (D) x 46 1/6" (H)
Weight
440 lbs.
Floor requirements
47 5/8" (W) x 31 5/16" (D)
Power source
120V AC, 60 Hz, 13 A (dedicated Line)
Rated Power consumption
Continuous copying: 1920W, 16 A
1. During preheat
198W or less
3. Shutoff
15W or less
2. Weekly Timer
20W or less
4. Printer unit installed
90W or less
Grounding
Isolation recommended
Termination
NEMA Type 5-20R receptacle (120V AC, 2-pole, 3-wire, grounded)
Note: A dedicated AC line with an isolated ground is strongly recommended. A dedicated line mandates the exclusive use of an electrical branch
circuit where the receptacle grounding terminal is grounded by an insulated grounding conductor that is isolated from the receptacle mounting
hardware (per National Electrical code, article 250-74, exception no. 4).
Options:
ST-11 (3,000 large paper deck), F-4330 (Finisher), F-4220 (Saddle Stitcher), Printer/Scan System, Mailbox (M-2107), Tandem Copy Kit
(TK-1) and Copy tray (for 120 V specifications only).
