Rover LS 33T Скачать руководство пользователя страница 18

Страница: 18 / 24

Troubleshooting

Problem

Cause

Remedy

Engine fails to start

1. Spark plug wire disconnected.

2. Fuel tank empty or stale fuel.

3. Choke, if equipped, not in CHOKE position.

4. Faulty spark plug.

5. Blocked fuel line.

6. Engine not primed properly (if equipped).

7. Throttle control lever not in correct starting

position.

1. Connect wire to spark plug.

2. Fill tank with clean, fresh fuel.

3. Move choke to CHOKE position.

4. Clean, adjust gap, or replace spark plug.

5. Clean fuel line.

6. Prime engine.

7. Move throttle lever to FAST position.

Engine running erratically/

inconsistent RPM (hunting

or surging)

1. Log splitter running with CHOKE applied (if

equipped).

2. Spark plug wire loose.

3. Blocked fuel line or stale fuel.

4. Water or dirt in fuel system.

5. Dirty air cleaner.

6. Carburetor not adjusted properly.

1. Move choke lever to RUN position.

2. Connect and tighten spark plug wire.

3. Clean fuel line; fill tank with clean, fresh (less

than 30 days old) fuel.

4. Drain fuel tank. Refill with fresh fuel.

5. Clean or replace air cleaner.

6. See authorized service dealer.

Engine Overheats

1. Engine oil level low.

2. Dirty air cleaner.

3. Carburetor not adjusted properly.

1. Fill crankcase with proper oil.

2. Clean or replace air cleaner.

3. See authorized service dealer.

Cylinder rod will not move

1. Broken drive shaft.

2. Set screws in coupling not adjusted properly.

3. Loose shaft coupling.

4. Gear sections damaged.

5. Damaged relief valve.

6. Hydraulic lines blocked.

7. Incorrect oil level.

8. Damaged directional valve.

9. Blocked directional valve.

1. See authorized service dealer.

2. See authorized service dealer.

3. Correct engine/pump alignment as

necessary.

4. See authorized service dealer.

5. See authorized service dealer.

6. Flush and clean hydraulic system.

7. Check oil level and fill as required.

8. See authorized service dealer.

9. Flush and clean hydraulic system.

Содержание LS 33T

























Результаты поиска

Содержание LS 33T

Отзывы:

Похожие инструкции для LS 33T

Бренды по названию

Популярные бренды

Rover LS 33T, Руководство оператора

Результаты поиска

Содержание LS 33T

Отзывы:

Похожие инструкции для LS 33T

Бренды по названию

Популярные бренды