Rover LS 33T, Руководство оператора, Страница: 16 / 24

16 S
ection
6— M
aintenance
& a
djuStMentS
6. Reinstall the filter inlet screen and suction hose. Tighten the hose
clamp.
7. Check the fluid level using the dipstick. Do not overfill.
NOTE:
Approved fluids include Shell Tellus® S2 M 32 Hydraulic
Fluid, Dexron® III/Mercon® automatic transmission fluid, Pro-
Select™ AW-32 Hydraulic Oil or 10WAW-ISO viscosity grade 32
hydraulic oil. It is recommended that fluids not be mixed.
8. Replace the vented dipstick securely, tightening it until the top of
the threads are flush with top of the pipe.
9. Disconnect the spark plug and prime the pump by pulling the
recoil starter as far as it will go. Repeat approximately 10 times.
10. Reconnect the spark plug wire and start the engine following the
instructions in the Engine Operator’s Manual.
11. Use the control handle to engage the wedge to the farthest
extended position. Then retract the wedge.
12. Refill the reservoir within range marked on the dipstick. See
Figure 6-4.
Dipstick
MAX
MIN
Hydraulic Fluid
Only
Figure 6-4
13. Extend and retract the wedge 12 complete cycles to remove
trapped air in the system (the system is “self-bleeding”).
WARNING!
Much of the original fluid has been drawn
into the cylinder and hoses. Make certain to refill the
reservoir to prevent damage to the hydraulic pump. Failure
to refill the tank will void the log splitter’s warranty.
NOTE:
Some fluid may overflow from the vent plug as the system
builds heat and the fluid expands and seeks a balanced level.
Do not operate the log splitter without the proper amount of
transmission fluid in the reservoir tank.
14. Maintain the fluid level within the range specified on the dipstick
at all times. When checking the fluid, always make sure to tighten
the dipstick until the top of the threads are flush with the top of
the pipe.
NOTE:
Always dispose of any used hydraulic fluid and engine oil
at approved recycling centers only.
15. Contaminants in the fluid may damage the hydraulic components.
Flushing the reservoir tank and hoses with kerosene whenever
service is performed on the tank, hydraulic pump or valve is
recommended. Contact an authorized service dealer.
Hose Clamps
Check the clamps on the return hose before each use and check the
clamps on the suction hose once a season.
Hydraulic Filter
Change the hydraulic filter every 50 hours of operation. Use a 10 micron
hydraulic filter only. Order part number 723-0405.
Beam & Splitting Wedge
Lubricate the top, sides and bottom of the beam and where it comes into
contact with the splitting wedge with engine oil before each use.
Off-Season Storage
If the log splitter will not be used for more than 30 days, prepare for
storage as follows:
WARNING!
Never store the machine with fuel in the
fuel tank inside of building where fumes may reach an
open flame or spark, or where ignition sources are present
such as hot water and space heaters, furnaces, clothes
dryers, stoves, electric motors, etc.
1. Refer to the Engine Operator’s Manual packed with your log
splitter for information on the off-season storage of the engine.
2. Clean the log splitter thoroughly.
NOTE:
The use of pressure washers or a garden hose to clean
the splitter is not recommended. They may cause damage to the
bearings or the engine. The use of water to clean the log splitter will
result in a shortened life and reduce serviceability.
3. Wipe the machine with an oiled rag to prevent rust, especially on the
wedge, beam and horizontal bracket.
4. Store the log splitter in a clean, dry area. Do not store it next to
corrosive materials, such as fertilizer.
NOTE:
If storing in an unventilated or metal storage shed, be certain
to rustproof the equipment by coating it with a light oil or silicone.