Rover LS 33T Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 24

background image

10

S

ection

3— A

SSembly

& S

et

-U

p

5.

Disconnect the spark plug and prime the pump by pulling the recoil

starter as far as it will go. Repeat approximately 10 times.

NOTE:

Close the fuel shut-off valve (if equipped) before performing

Step 5 to avoid engine flooding.

6.

Reconnect the spark plug wire and start the engine following

instructions in the Engine Operator’s Manual.

7.

Use the control handle to engage the wedge to the farthest

extended position. Then retract the wedge.

8.

Refill the tank as specified on the dipstick if necessary.

NOTE:

Failure to refill the tank will void the log splitter’s warranty.

9.

Extend and retract the wedge 12 complete cycles to remove any

trapped air in the system (the system is “self-bleeding”).

10.

Refill the reservoir within the range marked on the dipstick if

necessary.

NOTE:

Some fluid may overflow from the vent plug as the system

builds heat and the fluid expands and seeks a balanced level.

Tire Pressure

The max recommended operating pressure is 30 psi. Do not under any

circumstances exceed the manufacturer’s recommended psi. Maintain

equal pressure in both tires.

WARNING!

Excessive pressure when seating beads

may cause tire/rim assembly to burst with force sufficient

to cause serious injury.

«
...
8
9
10
11
12
...
»

Содержание LS 33T

























Отзывы:

Нет отзывов

Похожие инструкции для LS 33T

Бренд: ZIPPER MASCHINEN Страницы: 109

Бренд: Forstmeister Страницы: 22

Бренд: sunjoe Страницы: 12

Бренд: Range Road Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды