
Section 3 Safety
SG7 Manual
www.rottlermfg.com
3-2
KEEP WORK AREA CLEAN
. Cluttered areas and benches invite accidents.
KEEP CHILDREN AND VISITORS AWAY
. All children and visitors should be kept a safe distance from
work area.
WEAR THE PROPER APPAREL. DO NOT
wear loose clothing, gloves, rings, bracelets, or other jewelry
which may get caught in moving parts. Non-Slip foot wear is recommended. Wear protective hair
covering to contain long hair.
ALWAYS USE SAFETY GLASSES
. Also use face or dust mask if cutting operation is dusty. Everyday
eye glasses only have impact resistant lenses, they are NOT safety glasses.
DO NOT OVER-REACH
. Keep proper footing and balance at all times.
USE THE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. The
use of improper accessories may cause risk of injury.
CHECK DAMAGED PARTS.
Before further use of the machine, a guard or other part that is damaged
should be checked to determine that it will operate properly and perform its intended function. Check
for alignment of moving parts, breakage of parts, mounting, and other conditions that may affect its
operation. A guard or other part that is damaged should be properly repaired or replaced.
NEVER OPERATE A MACHINE WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR
ALCOHOL.
Full mental alertness is required at all times when running a machine.
IF AT ANY TIME YOU ARE EXPERIENCING DIFFICULTIES
performing the intended operation, stop
using the machine! Then contact our service department or ask a qualified expert how the operation
should be performed.
DO NOT MODIFY OR ALTER THIS EQUIPMENT
in any way. If modifications are deemed necessary, all
such requests must be approved and/or handled by Rottler Manufacturing. Unauthorized modifications
could cause injury and/or damage to machine and will void the warranty.
SAFETY DECALS SHOULD NEVER BE REMOVED
. They are there to convey important safety
information and warn of potential hazards.
ALL LOCAL SAFETY CODES AND REGULATIONS
should be followed when installing this machine.
ONLY QUALIFIED PERSONAL
should perform service on the electrical and control systems.
When boring the machine is capable of throwing metal chips over 10- feet from the cutting area. Always
use the guards. Eye protection must be worn at all times by the operator and all other personnel in the area
of the machine.
Содержание SG7
