
Section 2 Installation
SG7 Manual
www.rottlermfg.com
2-3
MACHINE START-UP
When starting the machine for the first time, it may move out of control. Make sure all
hands are clear of machine parts. Be ready to press the Emergency Stop button if
needed.
______Turn main power on from the main incoming breaker box.
MACHINE MOVEMENTS
______Make sure there is nothing obstructing the full vertical travel of the machine.
______When the machine is on the clamp mode and the air pressure is with the requirements, try to move
workhead to verify that you have a solid clamp of Work head.
______Place the level on the leveling post. The level assembly is referenced to the spindle via the level pin. It is
therefore important to check alignment of the pin in reference to the spindle. Even though the level has
been carefully calibrated at the factory, it is a good idea to recheck calibration before putting the machine
into service. In the event that the level is dropped or handled roughly then the following recalibration
methods should be implemented. If calibration is required refer to manual for Calibrating the Digital Level
______Start the spindle and verify operation.
INSTRUCTING THE OPERATOR:
______Fully explain the tilt of the work head and verify level buy rotating level 180.
______Using the operating manual as a guide explain the function of all buttons.
______Cycle all machine movements and supervise the handling of same by operator.
______Have operator sharpen a cutter bit if a sharpener has been supplied.
______Point out safety features to customer and operator.
Do not push any buttons without thinking of safety first.
______The following is a checklist to go through every time the machine is started to begin machining a seat.
•
Work piece secure
•
RPM set
•
Tool holder adjusted to the correct setting base on the type of seat you will be machining
•
Tool holder locked in place
•
Floating of the Workhead and clamping
______Proceed to have operator to machine a seat under you control.
______
Parts ordering, refer to the operating manual for part numbers and description.
______Review Emergency stop procedure and with operator per operating manual.
Содержание SG7
