background image

15

4. 

CK Atronik

4.2  Option Settings

Extra Relays

Atronik can accommodate four additional relay contacts with configurable functions. These are determined by DIP switches 
located on the extra relay PCB.

Switch 1

Switch 2

Switch 3

Relay 3 Function

Relay 4 Function

OFF

OFF

OFF

Open Limit

Closed Limit

OFF

OFF

ON

Torque Trip Open

Torque Trip Closed

OFF

ON

OFF

Blinker

Local Selected

OFF

ON

ON

Motor Stall

ESD Active

ON

OFF

OFF

Torque Trip

ESD Active

ON

OFF

ON

Hand Operation

ESD Active

ON

ON

OFF

Local Selected

Mid Travel

ON

ON

ON

Valve Alarm

24 VDC Power Fail

Switch 4

Switch 5

Switch 6

Relay 5 Function

Relay 6 Function

OFF

OFF

OFF

Closed Limit

Open Limit

OFF

OFF

ON

Torque Trip Closed

Torque Trip Open

OFF

ON

OFF

Mid Travel

Local Selected

OFF

ON

ON

Actuator Alarm

Hand Operation

ON

OFF

OFF

Stop Selected

Hand Operation

ON

OFF

ON

Remote Selected

Motor Running

ON

ON

OFF

Local Selected

Motor Running

ON

ON

ON

Mid Travel

Motor Running

Positioner

The positioner option for Atronik enables control of actuator position with a proportional analogue signal.  
Feedback is transmitted via 4-20 mA to provide remote intermediate position indication.

Switch No

Function

OFF

ON

SW5

6

Positioner Inverse

Control signal is:
Close = low, Open = high

Control signal is:
Close = high, Open = low

5

CPT Inverse

Feedback signal is:
Close = 4 mA, Open = 20 mA

Feedback signal is:
Close = 20 mA, Open = 4 mA

4

Signal Loss Action

SW5-3 OFF and SW5-4 OFF = Close
SW5-3 ON and SW5-4 OFF = OFF

SW5-3 ON and SW5-4 ON = Open
SW5-3 OFF and SW5-4 ON = Stayput

3
2

Input Type

SW5-1 OFF and SW5-2 OFF = 0-20 mA
SW5-1 ON and SW5-2 OFF = 0-5 V

SW5-1 ON and SW5-2 ON = 0-20 V
SW5-1 OFF and SW5-2 ON = 0-10 V

1

SW4

0 – 9

Deadband

10* position switch with incrementing values: 0.5%, 1%, 2%, 3%, 5%, 10%

SW3

0 – 9

Motion Inhibit Timer

10* position switch with incrementing values: 1s, 2s, 5s, 10s, 30s, 60s

SW1

Set Open

Inject signal for the Open position and hold SW1 for 3 seconds to set the value

SW2

Set Close

Inject signal for the Close position and hold SW2 for 3 seconds to set the value

Deadband and MIT should be adjusted to provide suitable control accuracy while still filtering out unwanted signal fluctuations and noise.
* Position 0 is the lowest setting, incrementing by one for each subsequent setting value. Surplus positions will match the highest setting 
value and are reserved for future use.

A4

US

US

A4

US

A4

US

A4

A4

US

 US

 A4

 US

 A4

A4

US

Содержание CK Atronik Series

















Отзывы: