Roto-Mix 425 Скачать руководство пользователя страница 30

Страница: 30 / 92

INSTALLING CHUTE AND PIVOT BAR
(OPTIONAL)

1. Assemble the chute and cylinder linkage as shown

in figure 13.

2. Connect the hydraulic piping as shown in the Re-

pair Parts - Hydraulic Components - Conveyor with

Chute section located in this book.

3. To adjust the folded position of the chute, raise the

conveyor fully and lock in this position using the stop

pin on the fold limiter arm. Next actuate the chute cyl-

inder causing the chute to fold fully. To reduce the

amount the chute folds, extend the cylinder to the de-

sired location and move the stop collar located on the

chute cylinder rod down the rod. To increase the

amount the chute folds, move the collar further up the

rod. Standard conveyers typically need to have the

stop collar set down the rod to prevent the chute from

contacting the mixer body. Due to their longer length,

extended conveyors typically can have the stop collar

set at the top of the cylinder. Further adjustment of the

chute position can be achieved by threading the Cylin-

der Extension further onto or off of the cylinder rod.

4. Typically the lowered position of the chute is limited

by the mechanical interference of the bottom of the

chute and the bottom of the conveyor. If however it

does not lower to this position, the cylinder extension

can be threaded off of the cylinder rod to tilt the chute

further down.

Page 30

FIGURE 13. CHUTE INSTALLATION

PIVOT BAR

STOP COLLAR

CHUTE CYLINDER

Содержание 425





























































































Результаты поиска

Содержание 425

Отзывы:

Похожие инструкции для 425

Бренды по названию

Популярные бренды

Roto-Mix 425, Руководство оператора

Результаты поиска

Содержание 425

Отзывы:

Похожие инструкции для 425

Бренды по названию

Популярные бренды