Roto-Mix 425 Скачать руководство пользователя страница 24

Страница: 24 / 92

ADJUSTMENTS - TRAILER & TRUCK MOUNTS

DISCHARGE CONVEYOR HEIGHT

The discharge chute height can be set by positioning

the stop pin in the desired hole of the fold limiter bar,

see figure 6.

CONVEYOR DRIVE CHAIN

There are adjusting nuts on each side of the conveyor.

Tighten or loosen these nut to allow approximately

1-1/4 inches between the bottom of the chain flight and

the conveyor pan when the chain is pulled up at the

center of the conveyor, see figure 7.

CHAIN IDLER SPRINGS

To maintain proper chain tension adjust the turn

buckle on each idler spring so the gap between the

coils is the thickness of a nickel. This should occur

when the spring is extended to 5-1/2 - 6-1/2 inches

measured outside of coil to outside of coil, see figure

8. If there is insufficient adjustment to achieve the

proper chain tension a full chain link should be re-

moved and replaced with an offset link.

TRAILER HITCH CLEVIS ADJUSTMENT
(TRAILER MOUNT ONLY)

Mixer should be approximately level when attached to

the tractor.

Adjust clevis by changing hole location on tongue.

Hitch Pin Size - 1” x 6”

ADJUSTMENT OF FOLDING CHUTE

The discharge chute is controlled actuated using a hy-

draulic cylinder located on the drive side of the con-

veyor. On trailer models, this cylinder plus those

controlling the door and conveyor actuation are pow-

Page 24

FIGURE 6.

ADJUST DISCHARGE HEIGHT

FOLD LIMITER BAR

STOP PIN

FIGURE 7.

ADJUST CONVEYOR CHAIN

(2) ADJUSTING NUTS

FIGURE 8. IDLER SPRINGS

4-5/8” FREE POSITION

5-1/2 - 6-1/2” EXTENDED

ALWAYS DISCONNECT AND LOCKOUT ELECTRICAL POWER (STATIONARY MODELS) OR DISENGAGE

POWER TAKE OFF AND REMOVE KEYS FROM TRACTOR (TRAILER MODELS) BEFORE CLEANING, AD-

JUSTING, LUBRICATING OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS

PERSONAL INJURY OR DEATH.

Содержание 425





























































































Результаты поиска

Содержание 425

Отзывы:

Похожие инструкции для 425

Бренды по названию

Популярные бренды

Roto-Mix 425, Руководство оператора

Результаты поиска

Содержание 425

Отзывы:

Похожие инструкции для 425

Бренды по названию

Популярные бренды