background image

Rotar Giga 75-100 - Cod.197AA3900 - Rev.03 - 05/2007

GB

15

15

15

15

15

2

3

1

MAINTENANCE

13

EVERY 15,000 OPERATING HOURS

MIN. PRESSURE valve (fig.13)
Open door (F) (see fig.7) and bleed all air off the tank through the cock (1).
Replace gaskets (2) and (3)

.

SERVICE TABLE - WARNING

Oil is an essential factor. When using an oil type which is different from the recommended one - RotEnergy Plus -  some service

intervals must be changed. Please refer to table.

In any case, a different oil MUST be used ONLY when oil is fully changed. NEVER MIX DIFFERENT TYPES OF OIL TOGETHER.

Never top up with a different type of oil.

EXHAUSTED OIL IS HIGHLY POLLUTANT! Dispose of exhausted oil in compliance with current laws.

Used oil 

RotEnergy Plus

Different compatible oil 

(see table)

Service description

Operating hours

Operating hours

Check and top up oil level

300

300

Clean intake filter and prefilter

500

500

Grease the electric motor bearings

4000

4000

Replace intake filter element 

2000

2000

Replace oil filter

4000

4000

Replace oil separator filter

4000

4000

Change oil

8000

4000

Check driving belt tension

10000

10000

Check min. pressure valve

15000

15000

Replace driving belt

20000

20000

Replace  compressor seal ring

20000

20000

Replace tank safety valve

20000

20000

Compatible oils: SHEEL Corena D46 - BP Energol HLP 46 - MOBIL  D.T.E. 
MEDIUM - AGIP Dicrea 46 - CASTROL  Aircol MR46 - ESSO Univis 46 -                                              
IP Veretum Oil 46 - FINA Eolan R046

Содержание Giga 100




















Отзывы: