Ross hyperSPARC Скачать руководство пользователя страница 5

Страница: 5 / 66

Chapter 4.
Installing the hyperSPARC Module in the SPARCstation 20

4-1

. . . . . . . . . . . . . . . . . . . . . . . . .

4.1 Removing the System Unit Cover

4-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2 Removing a Module

4-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3 Setting the MBus Clock Speed Jumper

4-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4 Removing and Replacing the Boot PROM

4-5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5 Installing or Replacing a Module

4-7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the hyperSPARC Module in MBus Slot 0 (Lower Slot)

4-7

. . . . . . . . . . . . . . . . . . . . . .

Installing the hyperSPARC Module in MBus Slot 1 (Upper Slot)

4-8

. . . . . . . . . . . . . . . . . . . . . .

4.6 Replacing the System Unit Cover

4-10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.7 Starting Up the System and Verifying Installation

4-11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 5.
Installing the hyperSPARC Module on the 600MP System Board

5-1

. . . . . . . . . . . . . . . . . . . . .

5.1 Handling System Boards and Assemblies

5-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2 Removing the System Board from the Enclosure

5-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3 Removing and Replacing the Boot PROMs

5-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4 Removing the Module

5-5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5 Installing or Replacing a Module

5-6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6 Installing the System Board in the Enclosure

5-8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7 Starting Up the System and Verifying Installation

5-9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Appendix A.
Troubleshooting Guide (Potential Upgrade Problems)

A-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A.1 Correct Patches for Solaris 1.1 Operating System

A-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A.2 Correct Patches for Solaris 2.3 and 2.4 Operating System

A-1

. . . . . . . . . . . . . . . . . . . . . . . . . .

A.3 hyperSPARC Operating System (OS) Compatibility

A-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A.4 Operating Systems NOT Compatible with hyperSPARC:

A-2

. . . . . . . . . . . . . . . . . . . . . . . . . . .

A.5 SunOS 4.1.4 Issues

A-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

A.6 Peripheral Problems

A-5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Appendix B.
Miscellaneous Technical Information

B-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B.1 How to identify the CPU(s) already installed in your machine:

B-1

. . . . . . . . . . . . . . . . . . . . . . .

B.2 Current boot PROM Revision Levels for Sun SPARCstation 10, 20, and

SPARCserver 600MP Machines

B-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B.3 Recommended Kernel Jumbo Patches:

B-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B.4 Identifying the CPU Configuration of hyperSPARC Modules

B-2

. . . . . . . . . . . . . . . . . . . . . . . . .

B.5 Identifying the Speed of a hyperSPARC Module

B-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Appendix C.
Warranty and RMA Information

C-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C.1 ROSS Technology Limited Warranty

C-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C.2 Returned Merchandise Authorization (RMA) Information

C-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Содержание hyperSPARC



































































Результаты поиска

Содержание hyperSPARC

Отзывы:

Ross hyperSPARC, Руководство по установке, Страница: 5 / 66

Результаты поиска

Содержание hyperSPARC

Отзывы: