Ross hyperSPARC Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 66

Ross hyperSPARC Скачать руководство пользователя страница 23

3-2

3.1 Removing the System Unit Cover

Caution: Make sure that power to your system unit is turned off. The power cord must remain plugged into
the system unit and to the power source to ensure a proper ground.

To remove the cover from the system unit:

1. Use a #2 Phillips screwdriver to fully loosen the captive screw holding the cover to the back panel.

The screw will remain attached to the back panel after it is fully loosened from the cover.

Captive screw

Figure 3-1. Location of Captive Screw on the Rear Panel

2. Use the Phillips screwdriver to press the retainer clip while you loosen the cover from the back panel

with your other hand.

Retainer clip

Figure 3-2. Location of the Retainer Clip

3. Grasp the sides of the cover from the rear and lift the cover as shown in Figure 3-3. Push the cover

forward until its hinge tabs are free of the system unit.

Figure 3-3. Removing the System Unit Cover, Side View

Warning: Before powering on your system again, be sure to install the cover. Refer to section 3.6 “Replacing
the System Unit Cover.” It is not safe to operate the SPARCstation 10 without the top cover in place.

«
...
21
22
23
24
25
...
»

Содержание hyperSPARC



































































Отзывы:

Нет отзывов