Ross hyperSPARC Скачать руководство пользователя страница 4

Страница: 4 / 66

iii

Contents

Chapter 1.
Before Installing the hyperSPARC Module

1-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 Before You Begin the Installation

1-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 Hardware Installation Overview

1-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Shutting Down the System

1-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tools Required for Module Installation

1-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrostatic Discharge Precautions

1-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3 Using the Disposable Wrist Strap

1-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 2.
Preparing to Install the hyperSPARC Module

2-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Overview

2-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Typographic Conventions

2-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Before You Begin the Installation

2-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3 Software Installation

2-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the Kernel Patch (for machines running Solaris 1.1 (SunOS 4.1.3) and
Solaris 1.1.1 (SunOS 4.1.3_U1) only)

2-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents of the Patch

2-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing from Local CD-ROM:

2-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing from Remote CD-ROM:
Part 1: On the system with the CD-ROM drive (upgrade server)

2-6

. . . . . . . . . . . . . . . . . . . . . .

Part 2: On the system being upgraded with the hyperSPARC
module (client)

2-6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4 Hardware Installation Overview

2-9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Shutting Down the System

2-9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tools Required for Module Installation

2-10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrostatic Discharge Precautions

2-10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5 Using the Disposable Wrist Strap

2-10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 3.
Installing the hyperSPARC Module in the SPARCstation 10

3-1

. . . . . . . . . . . . . . . . . . . . . . . . .

3.1 Removing the System Unit Cover

3-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2 Removing a Module

3-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3 Setting the MBus Clock Speed Jumpers

3-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Board with Three Jumpers

3-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Board with One Jumper

3-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4 Removing and Replacing the Boot PROM

3-5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5 Installing or Replacing a Module

3-7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the hyperSPARC Module in MBus Slot 0 (Lower Slot)

3-7

. . . . . . . . . . . . . . . . . . . . . .

Installing the hyperSPARC Module in MBus Slot 1 (Upper Slot)

3-8

. . . . . . . . . . . . . . . . . . . . . .

3.6 Replacing the System Unit Cover

3-10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.7 Starting Up the System and Verifying Installation

3-11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Содержание hyperSPARC



































































Результаты поиска

Содержание hyperSPARC

Отзывы:

Ross hyperSPARC, Руководство по установке, Страница: 4 / 66

Результаты поиска

Содержание hyperSPARC

Отзывы: