Romus sandy 2 CM33-43 F Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 22

Romus sandy 2 CM33-43 F Скачать руководство пользователя страница 2

The descriptions contained in this document are not binding.
The company therefore reserves the right to make any modifications at any time to parts,
details or accessory supply, as considered necessary for reasons of improvement or for
manufacturing/commercial requirements.
The reproduction, even partial, of the text and drawings contained in this document is prohibited
by law.

The company reserves the right to make any technical and/or supply modifications. The images
are shown as a reference only, and are not binding as to the actual design and/or equipment.

SYMBOLS USED IN THE MANUAL

Open book symbol with an "i"
Indicates the need to consult the instruction manual

Open book symbol:
Used to tell the operator to read the manual before using the machine

Warning symbol
Carefully read the sections marked with this symbol and observe the
indications, for the safety of the operator and the machine

Warning symbol
Indicates the risk of gas exhalation and leakage of corrosive liquids

Warning symbol
Indicates that the packed product should be handled with suitable lifting
means that comply with the legal requirements

«
1
2
3
4
...
»

Содержание sandy 2 CM33-43 F























Отзывы:

Нет отзывов