Romus sandy 2 CM33-43 F Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 22

Romus sandy 2 CM33-43 F Скачать руководство пользователя страница 16

ROMUS - Z.A. Les Pouards, 13 et 15 rue Taillefer 91160 CHAMPLAN – FRANCE

15

TROUBLESHOOTING

16. THERMAL

CUT-OUT

The single-disc machine is equipped with the following electrical protection systems, thermal cut-out
(1), located off the handlebars, to protect the motor. In the event of malfunctioning, check a thermal
cut-out has not intervened. If the motor overheats, its thermal cut-out intervenes to block the electricity
supply. Wait a few minutes until it has cooled down, then press the specific circuit breaker button to
reactivate the power supply and motor operation.

17. NOT ENOUGH DETERGENT SOLUTION ON THE BRUSH (OPTIONAL)

1.

Check that the valve allowing the detergent solution to flow from the tank to the brush is not
blocked. Flush the tank if needed.

2.

Check that the solution distribution pipe is not blocked. Flush it out if necessary.

18. THE MACHINE VIBRATES OR OSCILLATES

The machine has been sitting in rest position for too long, with the brush or pad holder still inserted.
Replace as soon as possible.

«
...
14
15
16
17
18
...
»

Содержание sandy 2 CM33-43 F























Отзывы:

Нет отзывов