13
« red hot » 15 kw
ref 93478
11
12.
Do not use the heater near or directly opposite furniture, animals, curtains, paper, clothes, bedding or other inflammable objects.
Keep them at least 1 metre away from the heater!
13.
Never cover a heater! The heater’s air inlets and outlets should never be obstructed in any way, so as to prevent the possibility of fire.
Never use the heater to dry clothes and do not place anything on top of the heater. Do not place it on soft surfaces such as beds or
deep-pile carpets, as they can block openings.
14.
Make sure that the air around the heater can circulate freely. Do not place the heater too close to walls or large objects and do not
place it under shelves, cupboards, and similar.
15.
Prevent foreign objects from entering the heater via the venting or exhaust openings as this may lead to electric shock, fire or
damage.
16.
Never leave the heater unattended when switched on. Always switch if off before removing the plug from the socket. Always unplug
the heater when not in use! Pull on the plug to remove from the socket, never pull on the cord.
17.
Always switch the heater off, unplug it and leave to cool down before:
-
cleaning the heater
-
carrying out maintenance to the heater
-
touching or moving the heater. Use the handle for this!
18.
This machine gets hot when it is in use. To prevent burns, do not let bare skin come into contact with hot surfaces.
19.
Do not use a timer or a similar product to automatically switch on the heater. Always perform safety checks before using the heater!
20.
Close supervision is necessary when the product is used near children or incapacitated persons. Do not let children use the
appliance as a toy. This appliance is not suitable to be operated by children or persons who have physical, sensory and/or mental
limitations, or by persons who have no knowledge of, or experience with, this appliance.
21.
Keep the heater clean. Dust, dirt and/or a build up of deposits in the heater are a common cause of overheating. Make sure these
deposits are removed regularly.
22.
Do not turn on the appliance if you have discovered damage to the appliance, cord or plug, if the appliance is malfunctioning, if it has
been dropped or if there are signs of any other defect. Return the complete product to the vendor or to a certified electrician for
inspection and/or repair. Always ask for original parts.
23.
Do not use attachments and/or accessories that have not been recommended or supplied by the manufacturer.
24.
The appliance (incl. cord and plug) may only be opened and/or repaired by properly authorised and qualified persons.
25.
Only use this heater for its intended purpose and as described in this instruction manual.
Not abiding by instructions 23, 24 and 25 may lead to damage, fire and/or personal injuries. A failure to adhere to these rules also
immediately nullifies the guarantee and vendor, importer and/or manufacturer do not take responsibility for any of the consequences!
IMPORTANT:
SIMPLY SWITCHING OFF THE FAN-HEATER
IS NOT SUFFICIENT WHEN YOU WANT TO CLEAN OR MOVE THE FAN-HEATER.
ALWAYS REMOVE THE PLUG FROM THE POWER SOCKET!
Description
EUROM EK heaters are ‘real space’ heaters, with a powerful fan which disseminates a great deal of air.
Cold air is sucked in at the back, heated, and then blown out as hot air. Because a relatively large quantity of air is sucked in and blown
out, the air expelled by the heater does not feel particularly hot. As a great deal of air is heated and blown out, however, the entire space
(not just the air around the heater!) is gradually warmed up.
Control panel EK5001:
The EK5001 control panel consists of two dials:
* The mode selector dial with 5 positions is located on the left.
From top to bottom:
-
O or off
-
fan only
Control panel « red hot » 15kw
12
-
2500W power (low)
-
5000W power (high)
-
5000W with extra fan
* The continuously adjustable thermostat dial is located on the right.
Control panel EK9002:
The EK9002 control panel consists of two dials:
* The mode selector dial with 4 positions is located on the left.
From top to bottom:
-
O or off
-
fan only
-
4500W power (low)
-
9000W power (high)
* The continuously adjustable thermostat dial is located on the right.
Control panel EK15002:
The EK15002 control panel consists of two dials:
* The mode selector dial with 5 positions is located on the left.
From top to bottom:
-
O or off
-
fan only
-
5000W power (low)
-
10.000W power (average)
-
15.000W power (high)
* The continuously adjustable thermostat dial is located on the right.
On the panel of the EK9002 and EK15002 also is the reset point (see Safety features).
Location and Connection
Remove all packaging material and keep out of reach of children. After removing packaging, check the appliance for damage or other
signs that could indicate a fault/defect/malfunction. In case of doubt, do not use the appliance, but contact your vendor for inspection
or replacement.
Choose a suitable location for the heater, i.e. at least one metre away from any obstructions, walls or inflammable materials (see also
safety instructions). Always ensure that the heater has sufficient space at the back to suck in air and at the front, to blow out hot air (1
metre).
Make sure the heater is always in an upright position on a solid, flat, horizontal and non-flammable surface.
Make sure the heater is switched off (switch to O position), then plug into a correctly functioning, properly grounded 400V-50Hz
socket. Only connect the heater to an
earthed
socket!
12
-
2500W power (low)
-
5000W power (high)
-
5000W with extra fan
* The continuously adjustable thermostat dial is located on the right.
Control panel EK9002:
The EK9002 control panel consists of two dials:
* The mode selector dial with 4 positions is located on the left.
From top to bottom:
-
O or off
-
fan only
-
4500W power (low)
-
9000W power (high)
* The continuously adjustable thermostat dial is located on the right.
Control panel EK15002:
The EK15002 control panel consists of two dials:
* The mode selector dial with 5 positions is located on the left.
From top to bottom:
-
O or off
-
fan only
-
5000W power (low)
-
10.000W power (average)
-
15.000W power (high)
* The continuously adjustable thermostat dial is located on the right.
On the panel of the EK9002 and EK15002 also is the reset point (see Safety features).
Location and Connection
Remove all packaging material and keep out of reach of children. After removing packaging, check the appliance for damage or other
signs that could indicate a fault/defect/malfunction. In case of doubt, do not use the appliance, but contact your vendor for inspection
or replacement.
Choose a suitable location for the heater, i.e. at least one metre away from any obstructions, walls or inflammable materials (see also
safety instructions). Always ensure that the heater has sufficient space at the back to suck in air and at the front, to blow out hot air (1
metre).
Make sure the heater is always in an upright position on a solid, flat, horizontal and non-flammable surface.
Make sure the heater is switched off (switch to O position), then plug into a correctly functioning, properly grounded 400V-50Hz
socket. Only connect the heater to an
earthed
socket!
12
-
2500W power (low)
-
5000W power (high)
-
5000W with extra fan
* The continuously adjustable thermostat dial is located on the right.
Control panel EK9002:
The EK9002 control panel consists of two dials:
* The mode selector dial with 4 positions is located on the left.
From top to bottom:
-
O or off
-
fan only
-
4500W power (low)
-
9000W power (high)
* The continuously adjustable thermostat dial is located on the right.
Control panel EK15002:
The EK15002 control panel consists of two dials:
* The mode selector dial with 5 positions is located on the left.
From top to bottom:
-
O or off
-
fan only
-
5000W power (low)
-
10.000W power (average)
-
15.000W power (high)
* The continuously adjustable thermostat dial is located on the right.
On the panel of the EK9002 and EK15002 also is the reset point (see Safety features).
Location and Connection
Remove all packaging material and keep out of reach of children. After removing packaging, check the appliance for damage or other
signs that could indicate a fault/defect/malfunction. In case of doubt, do not use the appliance, but contact your vendor for inspection
or replacement.
Choose a suitable location for the heater, i.e. at least one metre away from any obstructions, walls or inflammable materials (see also
safety instructions). Always ensure that the heater has sufficient space at the back to suck in air and at the front, to blow out hot air (1
metre).
Make sure the heater is always in an upright position on a solid, flat, horizontal and non-flammable surface.
Make sure the heater is switched off (switch to O position), then plug into a correctly functioning, properly grounded 400V-50Hz
socket. Only connect the heater to an
earthed
socket!
« Red Hot » 15kw
12
-
2500W power (low)
-
5000W power (high)
-
5000W with extra fan
* The continuously adjustable thermostat dial is located on the right.
Control panel EK9002:
The EK9002 control panel consists of two dials:
* The mode selector dial with 4 positions is located on the left.
From top to bottom:
-
O or off
-
fan only
-
4500W power (low)
-
9000W power (high)
* The continuously adjustable thermostat dial is located on the right.
Control panel EK15002:
The EK15002 control panel consists of two dials:
* The mode selector dial with 5 positions is located on the left.
From top to bottom:
-
O or off
-
fan only
-
5000W power (low)
-
10.000W power (average)
-
15.000W power (high)
* The continuously adjustable thermostat dial is located on the right.
On the panel of the EK9002 and EK15002 also is the reset point (see Safety features).
Location and Connection
Remove all packaging material and keep out of reach of children. After removing packaging, check the appliance for damage or other
signs that could indicate a fault/defect/malfunction. In case of doubt, do not use the appliance, but contact your vendor for inspection
or replacement.
Choose a suitable location for the heater, i.e. at least one metre away from any obstructions, walls or inflammable materials (see also
safety instructions). Always ensure that the heater has sufficient space at the back to suck in air and at the front, to blow out hot air (1
metre).
Make sure the heater is always in an upright position on a solid, flat, horizontal and non-flammable surface.
Make sure the heater is switched off (switch to O position), then plug into a correctly functioning, properly grounded 400V-50Hz
socket. Only connect the heater to an
earthed
socket!
Red Hot
Romus
