Rolls-Royce Helicon X3 Скачать руководство пользователя страница 85

Страница: 85 / 140

Maintenance Instructions

Page 11 of 22

Doc. No.: 13S000411
Revision: A

To replace the controller (Rolls-Royce Marine Controller), proceed as following:
1.

Disconnect the power supply cable (1).

2.  Remove the Compact Flash memory (2).
3.  Disconnect the alarm connector (3).
4.  Disconnect the following connectors:

• CAN (4)
• Ethernet (5)
• RS 422 (6)

5.  Loosen the 6 screws that hold the controller in place, and remove the controller.
6.  Insert the Compact Flash memory in the new controller unit.
7.  Fit and connect the new controller in reverse order.

4.10 Replacing a CAN I/O Module

The CAN I/O module is located in the Control Cabinet. To change the internal circuit

board, proceed as following:
1.

Disconnect the power and CAN connector (2), which is located in the front.

2. Disconnect the I/O connector (3).

Ethernet

RS 422

Pos

Component

Screws

Power and CAN connector

I/O connector

Address node wheels

Jumpers

Software ID-tag

Pos

Component

Содержание Helicon X3


















































































































Результаты поиска

Содержание Helicon X3

Отзывы:

Похожие инструкции для Helicon X3

Бренды по названию

Популярные бренды

Rolls-Royce Helicon X3, Руководство пользователя

Результаты поиска

Содержание Helicon X3

Отзывы:

Похожие инструкции для Helicon X3

Бренды по названию

Популярные бренды