Rolls-Royce Helicon X3 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 140

background image

This document is the property of Rolls-Royce and may not be redistributed or reproduced in any way, without the written permission of Rolls-Royce.
Failure to do so is a violation of copyright laws.

P&T Control_20-12-00136_UT535E_Brasil _V2

Page 10 of 14

Interface to external systems

Interface to drive motor starter. (Project dependent. To be settled at interface meeting)

-

Drive motor RPM order signal, 4 - 20 mA.

The signal has to be galvanic isolated at the governor side.

-

RPM feedback signal

4-20mA signal from the frequency converter. Closed when frequency converter fault.

-

Common Alarm Drive RPM (Reduce load)

Potential free contact from the frequency converter. Closed = frequency converter alarm

-

Frequency Converter fault/ trip (autostop).

Potential free contact from the frequency converter. Closed = frequency converter fault.

-

Frequency Converter reset.

Potential free contact to the frequency converter. Closed = reset (pulse)

-

Start Frequency Converter

Potential free contact to the frequency converter. Closed = start (pulse)

-

Stop/ Autostop Frequency Converter

Potential free contact to the frequency converter. Closed = stop (pulse)

-

Emergency Stop Frequency Converter

Potential free contact to the frequency converter. Closed = stop (pulse)
Loop monitored in Frequency Converter (resistors in each control panel)

-

Interlock start/Auto stop Motor

In case of too low gear lub. oil pressure, a potential free relay contact is given to the engine control
system for immediately stop of the engine.
Open = stop.

-

Frequency Converter ready to run if handle out of zero.

Potential free contact from the frequency converter.
Closed = frequency converter started.

-

Power limitation.

Potential free contact from the frequency converter. Closed = power limited in drive.

-

Local/ emerg. control

Potential free contact from the frequency converter. Closed = local

DP Interface

The remote control is provided with interface for an ICON DP system.
Communication is via Ethernet.
(Other DP system will be interfaced through hardwired signals)

Signals required from the DP system:

-

Closing contact (potential free) to engage the DP mode. (From selector switch).

-

Request for control.

-

Speed control signal

-

Steering control signal

Signals available to the DP system:

-

Remote control is ready for DP

-

Remote control acknowledge of DP mode.

-

Propeller RPM feedback signal

-

Steering feedback signal

-

Power reduced signal

«
...
42
43
44
45
46
...
»

Содержание Helicon X3













































































































































Отзывы:

Нет отзывов

Похожие инструкции для Helicon X3

Бренд: jbc Страницы: 4

Бренд: halstrup-walcher Страницы: 39

Бренд: Eaton Страницы: 2

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Z3-DM8107-SDI-RPS

Бренд: Z3 Technology Страницы: 73

Бренд: Z-Wave Страницы: 14

Бренд: Z-Wave.Me Страницы: 4

Бренд: Saluki Страницы: 13

Бренд: Parker Страницы: 4

Бренд: Grundfos Страницы: 16

Бренд: Loewe Страницы: 62

Бренд: Shimaden Страницы: 32

Ratio Feeder J+ Advanced Series

Бренд: H.E. Anderson Страницы: 11

Бренд: Daikin Страницы: 8

Бренд: Silverline Страницы: 16

Бренд: Astrosyn Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды