background image

© 2015 Rollease Acmeda

© 2015 Rollease Acmeda

2. INSTALLATION

2.1 WARNING: Important safety instructions to be read before installation.

 

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

• 

Installation and programming to be performed by a suitably qualified installer.

• 

For use within tubular blinds & awnings.

• 

Ensure correct crown and drive adaptors are used for the intended system.

• 

Use only Rollease Acmeda hardware.

• 

Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation.

• 

Ensure torque and operating time is compatible with end application.

• 

Do not expose the motor to water or install in humid or damp environments.

• 

Tube and the drive adaptor should be evenly fixed with 4 pieces of 4x10 countersunk self-tapping screws. Ensure 
screw tip does not penetrate through the internal surface of the drive.

• 

Motor is to be installed in horizontal application only.

• 

Do not drill into motor body.

• 

For awning installation, a horizontal distance of at least 0,4m is to be maintained between the fully unrolled 
driven part and any obstacle.

• 

Ensure at least one control point is located within direct sight of unit but away from any moving parts.

• 

The routing of cable through walls shall be protected by isolating bushes or grommets.

• 

Ensure power cable and aerial is clear and protected from moving parts.

• 

Power supply cables are not be exposed to sunlight and must be protected by U.V resistant conduit.

• 

Ensure power is isolated prior to connecting or disconnecting inline connector.

• 

If cable or inline connector is damaged do not use.

Page. 3 of 12

Содержание Automate FT













Отзывы: