3 Day Blinds VINYL BLINDS Скачать руководство пользователя страница 1

Страница: 1 / 10

| Vinyl Blinds

GETTING STARTED

Steel Tape Measure

Power Drill and

Drill Bits

Awl (or tool for starting

a screw hole)

Level

Pencil

Flathead & Phillips

Screwdriver

Included in your order is all the hardware necessary for a

normal installation. Depending on the mounting surface,

fasteners other than the screws provided may be required.

Wall board and plaster require the use of anchors such as

expansion or toggle bolts. Bricks, tile and stone need special

plugs and drill bits. Wood should always be pre-drilled to

avoid splitting.
Professional installation is also available in most areas,

call 800-800-3329.

A few simple tools are required:

VINYL BLINDS

STANDARD HARDWARE

End Brackets

(Open Position LH & RH)

Screws

Center Support

Bracket(s)

Regular Valance Clips

Button Valance Clips

Outside Mount

Slat Valance

Inside Mount

Slat Valance

Содержание VINYL BLINDS











Результаты поиска

Содержание VINYL BLINDS

Отзывы:

Похожие инструкции для VINYL BLINDS

Бренды по названию

Популярные бренды

3 Day Blinds VINYL BLINDS, Начало работы

Результаты поиска

Содержание VINYL BLINDS

Отзывы:

Похожие инструкции для VINYL BLINDS

Бренды по названию

Популярные бренды