background image

|  Vinyl Blinds

9

•  At the top of the tilt wand 

(provided separately), 

you will find a plastic 

sleeve that covers a metal 

hook.

•  Remove the plastic sleeve 

on the tilt wand by pulling 

gently upward.

•  Make sure the metal hook 

attached to the tilt wand 

is in the open position.

•  On one end of the 

headrail, you will find a 

small metal shaft with a 

hole protruding from the 

headrail.

•  Take the plastic sleeve 

you just removed from 

the tilt wand and slide 

it up and over the shaft 

protruding from the 

headrail so that the hole 

at the end of the shaft is 

exposed.

•  Insert the metal hook into 

the hole in the shaft.

•  Slide the plastic sleeve 

down the shaft and over 

the tilt wand hook until it 

is secure.

TILT WAND ATTACHMENT

(Not applicable for blinds ordered with a cord tilt)

BLIND  OPERATION

•  To tilt the slats, twist the tilt wand. If you ordered a cord 

tilt, YOU MUST take one cord in each hand applying slight 

tension to each cord, and pull gently down to tilt the slats to 

the desired angle.

•  Do not attempt to raise or lower the blind unless the slats 

are in a completely open (horizontal) position.

•  To raise the blind, pull the lift cords down.
•  To engage the lock, pull the lift cords down and toward the 

outside of the blind.

•  To lower the blind, pull the lift cords down and toward 

the center of the blind and allow the cords to slide slowly 

through your hand.

Содержание VINYL BLINDS











Отзывы: