background image

|  Vinyl Blinds

3

•   If your hardware packet includes one center support 

bracket, position it as close to the top center of the window 

casing as possible. If more than one center support bracket 

has been provided, position them equidistant from the end 

brackets and each other.

WARNING: Do not locate the center support brackets over 

any of the moving parts in the headrail.

TO INSTALL CENTER SUPPORT BRACKETS:

•  Align the back of the center 

support bracket(s) with the 

back end of the mounting 

brackets. The alignment 

is crucial for proper blind 

installation.

•  Mark the window casing 

through the holes in the 

top of the center support 

bracket. For maximum 

stability, the marks should be 

made diagonally.

•  Using a drill with a  

1

/

16

" drill 

bit or an awl, make a small 

pilot hole at each mark.

•  Mount each of the bracket(s) 

using two of the screws 

provided.

Proceed to “Valance Blind Installation”.

OUTSIDE MOUNT

•  Unwrap the cellophane from around the blind stack. 

Caution: DO NOT cut the cellophane as the cords or ladders 

supporting the blind may be inadvertently cut.

•  Lower the blind to its full length. (See “Blind Operation”.)

1

/

8

"

•  Hold the blind up to the 

desired mounting position.

•  Once the blind is level, 

mark the wall at the lower 

corners of each end of the 

headrail using a pencil

•  Draw the blind completely up and set it aside.

•  Using a flathead 

screwdriver, open the 

latches of the end 

brackets.

•  Facing the window, 

position the end bracket 

marked “LH” above the 

top left corner of the 

window, 

1

/

8

" TO THE LEFT 

of the pencil marks.

•  Using a pencil, mark the 

wall through the holes 

in the back of the end 

bracket. For maximum 

stability, the pencil 

marks should be made 

diagonally.

•  Using a drill with a 

1

/

16

" drill 

bit or an awl, make a small 

pilot hole at each pencil 

mark.

•  Mount the bracket using 

the 2 screws provided.

•  Repeat this procedurre for 

the right end bracket.

Содержание VINYL BLINDS











Отзывы: