rollease acmeda Automate FT Скачать руководство пользователя

Страница: 2 / 12

CONTENTS

1. Compatible Controllers

2. Installation

2.1 WARNING: Important Safety instructions to be read before installations

2.2 Assembly

2.3 Wiring Diagram

3. Programming & Use

3.1 Warning: Important safety instructions to be read prior to operation

3.2 Overview of P2 function – How to activate setting mode

3.3 Overview of operational modes

3.4 Pairing motor to transmitter

3.5 Setting top & bottom limits

3.6 Set Favourite position

3.7 Impact Detection

3.8 Copy Channel from an existing primary transmitter

3.9 Activate / Deactivate Fabric Tension Mode

p10

3.10 Switch between Auto & Manual Lock Mode

p10

3.11 Adjusting Tension Level

p10

4. Troubleshooting

p11

COMPATIBLE CONTROLLERS

RF500s

RF400s

A.R.T | Wind & Light Sensors

A.R.T | Motion Sensor

Page. 2 of 12

Содержание Automate FT













Результаты поиска

Содержание Automate FT

Отзывы:

Похожие инструкции для Automate FT

Бренды по названию

Популярные бренды

rollease acmeda Automate FT, Инструкция по эксплуатации

Результаты поиска

Содержание Automate FT

Отзывы:

Похожие инструкции для Automate FT

Бренды по названию

Популярные бренды