background image

 

8

 

10.

 

Mount the kick pedal on the KD-120.

 

* Make sure there is about 1 cm of space between the two to 

keep the kick pedal’s chain (or belt) from touching the hoop 

of the KD-120 pad during play. Also, if the kick pedal has no 

under-plate, then arrange the stand’s plate section at a right 

angle to the floor.

 

fig.12.e

 

11.

 

Make any fine adjustments necessary and tighten 
the stand brackets to make sure the KD-120 is 
secure on the stand.

 

Make sure the KD-120’s four legs and heel portion of the kick 

pedal is securely on the floor by loosening the stand’s T-bolts 

and adjusting the length of the legs.

*  If the kick pedal has no under-plate, then arrange the stand’s 

plate section at a right angle to the floor.

 

12.

 

Adjust the striking point for the beater.

 

Normally the beater’s striking point is adjusted to fall at the 

center of the head.

Adjust the striking point so that it doesn’t extend beyond the 

cushion on the back of the head. Moving the striking point 

closer to the sensor increases the sensitivity, so carry out fine 

adjustment to suit your preferences.

 

When the Head Should Be Replaced

 

The head is an expendable item that eventually will wear out 

and need to be replaced. Replace the head when the 

following occurs:

• The head surface is torn

• Slack portions remain in the head even after the head tension 

is properly adjusted.

 

Replacing the Head

 

Do not apply excessive force to the sensor and cushion 

located under the head. Doing so can interfere with 

accurate detection, and may damage it.

 

1.

 

Remove all tuning bolts.

 

Go around and loosen each bolt a little at a time by turning it 

counter-clockwise.

 

2.

 

Remove the hoop.

 

3.

 

Remove the old head.

 

4.

 

Place the new head on the shell.

 

5.

 

Place the hoop on the head.

 

6.

 

Install all six tuning bolts.

 

7.

 

Adjust the tension of the head. Refer to  “Adjusting 
the Head Tension” (p. 6).

 

With the KD-120, you can also play using a twin (double kick) 

pedal.

Set this up so that the striking points of the two beaters fall at 

equal distances to the left and right of the center of the head.

 

fig.13

 

* When using a twin (double kick) pedal, as with a regular 

pedal, use the included beater or a plastic beater as the 

beater for the kick pedal.

If the kick pedal has no under-plate, then arrange 
the stand’s plate section at a right angle to the floor.

90˚

Prevent contact
between the
hoop and plate.

Allow sufficient
clearance
here.

 

Replacing the Head

When Using a Twin (Double Kick) Pedal

TD-12KX_e.fm 8 ページ 2009年11月10日 火曜日 午後12時6分

Содержание V-Drums TD-12KX

















Отзывы: