Roland TM-6 PRO, Список данных

Страница: 30 / 37

30
TRIGGER SETUP
Parameter Value Explanation
Tone 0–127 Tone quality of the Overdrive effect
Amp Sw OFF, ON Turns the Amp Simulator on/off.
Amp Type
SMALL, BUILT-IN,
2-STACK, 3-STACK
Type of guitar amp
SMALL: small amp
BUILT-IN: single-unit type amp
2-STACK:
large double stack amp
3-STACK: large triple stack amp
Low Gain -15–+15dB Gain of the low range
High Gain
-15–+15dB Gain of the high range
Pan L64–63R Stereo location of the output sound
Level 0–127 Output Level
DISTORTION
This is a distortion effect that provides heavy distortion. The
parameters are the same as for “OVERDRIVE.”
T-SCREAM
This models the analog overdrive of the past.
It adds a nice amount of overtones without dirtying the sound.
Parameter Value Explanation
Distortion(#) 0–127
Degree of distortion
Also changes the volume.
Tone 0–127 Sound quality of the Overdrive effect
Level
0–127 Output level
LOFI COMPRESS
This is an effect that intentionally degrades the sound quality for
creative purposes.
Parameter Value Explanation
Pre Filter Type 1–6
Selects the type of filter applied to
the sound before it passes through
the Lo-Fi effect.
1:
Compressor off
2–6: Compressor on
LoFi Type
1–9
Degrades the tone character. The
tone character grows poorer as this
value is increased.
Post Filter Type OFF, LPF, HPF
Selects the type of filter applied to
the sound after it passes through the
Lo-Fi effect.
OFF:
no filter is used
LPF:
cuts the frequency range above
the Cutoff
HPF:
cuts the frequency range below
the Cutoff
PostFltr Cutoff 200–8000Hz Basic frequency of the Post Filter
Low Gain
-15–+15dB Gain of the low range
High Gain -15–+15dB Gain of the high range
Balance(#)
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
Level 0–127 Output level
BIT CRUSHER
This creates a lo-fi sound.
Parameter Value Explanation
Sample Rate(#) 0–127 Adjusts the sample rate.
Bit Down 0–20 Adjusts the bit depth.
Filter(#) 0–127 Adjusts the filter depth.
Low Gain -15–+15dB Gain of the low frequency range
High Gain -15–+15dB Gain of the high frequency range
Level
0–127 Output level
SPEAKER SIM
Simulates the speaker type and microphone settings used to record
the speaker sound.
Parameter Value Explanation
SP Type(#)
SMALL 1, 2,
MIDDLE,
JC-120,
BUILT-IN 1–5,
BG STACK 1, 2,
MS STACK 1, 2,
METAL STACK,
2-STACK, 3-STACK
Type of speaker
Mic Setting 1–3
Adjusts the location of the
microphone that is recording the
sound of the speaker.
This can be adjusted in three steps,
with the microphone becoming
more distant in the order of 1, 2,
and 3.
Mic Level 0–127 Volume of the microphone
Direct Level 0–127
Volume of the direct sound (the
sound with the speaker turned off)
Level 0–127 Output level
GUITAR AMP SIM
This is an effect that simulates the sound of a guitar amplifier.
Parameter Value Explanation
Amp Sw OFF, ON Turns the amp switch on/off.
Amp Type(#)
JC-120, CLEAN
TWIN, MATCH
DRIVE,
BG LEAD,
MS1959I,
MS1959II,
II,
SLDN LEAD,
METAL 5150,
METAL LEAD,
OD-1,
OD-2 TURBO,
DISTORTION,
FUZZ
Type of guitar amp
Amp Volume 0–127
Volume and amount of distortion of
the amp
Amp Master 0–127 Volume of the entire pre-amp
Amp Gain
LOW, MIDDLE,
HIGH
Amount of pre-amp distortion
Amp Bass 0–127
Tone of the bass/mid/treble
frequency range
* Middle cannot be set if “MATCH
DRIVE” is selected as the Pre Amp
Type.
Amp Middle
0–127
Amp Treble 0–127
Amp Presence 0–127
Tone for the ultra-high frequency
range
Amp Bright OFF, ON Specifies the bright on/off setting.
Speaker Sw
OFF, ON Turns the speaker simulator on/off