Roland TM-6 PRO, Список данных

Страница: 29 / 37

29
TRIGGER SETUP
Parameter Value Explanation
Character 1–6 Type of reverb
EQ Low Freq 200–400Hz Center frequency of the low region
EQ Low Gain -15–+15dB Gain of the low range
EQ High Freq
2000–8000Hz Center frequency of the high region
EQ High Gain -15–+15dB Gain of the high range
Level 0–127 Output level
SUPER FILTER
This is a filter with an extremely sharp slope. The cutoff frequency
can be varied cyclically
Parameter Value Explanation
Filter Type
Filter type
Frequency range that will pass through each filter
LPF
Frequencies below the cutoff
BPF
Frequencies in the region of the
cutoff
HPF Frequencies above the cutoff
NOTCH
Frequencies other than the region of
the cutoff
Filter Slope
Amount of attenuation per octave
-12 dB
Gentle
-24 dB Steep
-36 dB Extremely steep
Filter Cutoff(#)
0–127
Cutoff frequency of the filter
Increasing this value will raise the
cutoff frequency.
Filter Resonance
0–100
Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency.
Filter Gain 0–+12 dB Amount of boost for the filter output
Modulation Sw OFF, ON On/off switch for cyclic change
Modulation Wave
How the cutoff frequency will be modulated
TRI
Triangle wave
SQR Square wave
SIN Sine wave
SAW1 Sawtooth wave (upward)
SAW2 Sawtooth wave (downward)
SAW1 SAW2
Tempo Sync OFF, ON
Specifies whether the modulation
rate is specified as a note value (ON)
or not (OFF).
Rate
0.05–10.00Hz,
note
Rate of modulation
Depth 0–127 Depth of modulation
Attack 0–127
Speed at which the cutoff frequency
will change
This is effective if Modulation Wave is
SQR, SAW1, or SAW2.
Level 0–127 Output level
DRIVE
This is a low-pass filter equipped with overdrive. It cuts the upper
range and adds distortion.
Parameter Value Explanation
Cutoff
Frequency(#)
0–127
Cutoff frequency of the filter
Increasing this value will raise the
cutoff frequency.
Filter
Resonance(#)
0–127
Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency.
Drive 0–127 Amount of distortion
Level
0–127 Output level
AUTO WAH
Cyclically controls a filter to create cyclic change in timbre.
Parameter Value Explanation
Filter Type
LPF, BPF
Type of filter
LPF: The wah effect will be applied
over a wide frequency range.
BPF: The wah effect will be applied
over a narrow frequency range.
Manual 0–127
Adjusts the center frequency at
which the effect is applied.
Peak
0–127
Width of the frequency region at
which the wah effect is applied
Increasing this value will make the
frequency region narrower.
Sens 0–127
Adjusts the sensitivity with which the
filter is controlled.
Polarity UP, DOWN
Direction in which the filter will move
UP: Move toward a higher frequency
DOWN:
Move toward a lower
frequency
Tempo Sync OFF, ON
Specifies whether the modulation
rate is specified as a note value (ON)
or not (OFF).
Rate(#)
0.05–10.00Hz,
note
Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180deg
Adjusts the degree of phase shift of
the left and right sounds when the
wah effect is applied.
Low Gain -15–+15dB Gain of the low range
High Gain
-15–+15dB Gain of the high range
Level 0–127 Output level
SATURATOR
A saturator which distorts the sound is connected in parallel with
a compressor, producing a rougher tonal character and boosting
the loudness. This also cuts the low-frequency region of the input
audio.
Parameter Value Explanation
Saturator Gain
0–127 Input volume to the saturator
Saturator Drive 0–127 Degree of distortion
Saturator Level(#) 0–127 Output volume of the saturator
Comp Depth
0–127 Amount of compression
Comp Level 0–127 Output volume of the compressor
Hi Gain
-12–+6dB Gain of the high range
Level 0–127 Output level
OVERDRIVE
This is an overdrive that provides heavy distortion.
Parameter Value Explanation
Drive(#) 0–127
Degree of distortion
Also changes the volume.