Roland LEC-300, Руководство пользователя

Страница: 137 / 150

6-8 If an Error Message Appears
135
Chapter 6 What to Do If
[HEAD HEIGHT ERROR]
The height-adjustment lever for the print heads was
operated improperly.
Operation cannot be continued. Switch the sub power off, then
back on. To change the head height, use the [HEAD HEIGHT]
menu.

P. 89, "Adjusting Head Height to Match Media Thickness"
[TEMPERATURE IS TOO LOW **°C]
The temperature of the location where the machine
is installed has fallen below the ambient temperature
at which the machine can operate.
Operation cannot be continued. Switch off the sub power. The
displayed temperature is the current ambient temperature of the
installation location. Bring the installed location to a temperature
at which operation is possible (20 to 32°C) and allow the machine
to come to room temperature, then turn on the power.
[DATA ERROR CANCELING...]
Output was stopped because a problem was found
in the data received.
Operation cannot be continued. Check whether the data
contains errors. Also, check for a problem with the connector
cable or the computer, and redo the operation from the step of
loading the media.
[PINCHROLL ERROR LOWER PINCHROLL]
was pressed without first lowering the pinch
rollers.
Press any key to clear the error. Pull back the loading lever, then
press
.
The pinch rollers were raised while was il-
luminated.
The error is cleared automatically after a short wait. Never move
the loading lever while printing is in progress.
[PINCHROLL ERROR INVALID RIGHT POS]
The right pinch roller is positioned at a location where
it does not pinch the media.
Raise the loading lever and move the right pinch roller to the
correct location.

P. 38, "Cutting Off Media"
[PINCHROLL ERROR INVALID LEFT POS]
The left pinch roller is positioned at a location where
it does not pinch the media.
Raise the loading lever and move the left pinch roller to the
correct location.

P. 31, "Loading and Cutting Off Media"
[WRONG CARTRIDGE]
A ink cartridge that cannot be used was installed.
Remove the ink cartridge to clear the error. Use a cartridge of
the specified type.
[AVOIDING DRY-UP TURN OFF POWER]
The print heads were forced to standby position to
prevent them from drying out.
Operation cannot be continued. Switch the sub power off, then
back on. Opening the front cover while printing is in progress
causes an emergency stop. Never allow the print heads to remain
in this state.
[MOTOR ERROR TURN POWER OFF]
A motor error occurred.
Operation cannot be continued. Switch off the sub power. Next,
eliminate the cause of the error, then immediately switch on the
sub power. If the machine is allowed to stand with the error un-
corrected, the print heads may dry out and become damaged.
This error may be caused by such factors as a mistake in loading
the media, a media jam, or an operation that pulls the media
with excessive force.
The media has jammed.
Carefully remove the jammed media. The print heads may also
be damaged. Perform head cleaning, then perform a printing
test and check the results.
The media was pulled with excessive force.
Excessive tension was applied to the media, and additional
action is necessary to recover from this state. First, move the
loading lever to the rear and adjust the media to create a small
amount of slack, then switch on the sub power.
[CANCELED FOR MOTOR PROTECTION]
Continuous operation made the pump motor become
hot, and so operation was paused.
Press any key to clear the error. Allow the machine to stand for
approximately 40 minutes before resuming operation.
[LONG MEDIA CLAMP IS INSTALLED]
Media cutoff was attempted even though [MEDIA
CLAMP] is set to “LONG.”
To prevent malfunction or damage to the machine, media-cutoff
operations are not performed when [MEDIA CLAMP] is set to
“LONG.” Use
to go back to the original screen, then either
detach the media clamps, or replace them with short media
clamps and set [MEDIA CLAMP] to “SHORT.”

P. 38, "Cutting Off the Media"