Roland LEC-300 Скачать руководство пользователя | Manualshive

Страница: 120 / 150

background image

118

Chapter 5 Feature Reference

5-12 Performing Maintenance

Draining Ink and Performing Internal Washing

Procedure



Press

.

Press

several times.



Press

.

Press

twice.



Press

.

Press

twice.

Press

to execute.

Description

This drains the ink inside the printer and washes the interior using cleaning SOL INK cartridges as a preliminary for moving
the printer or conducting maintenance. This operation requires four unused cleaning SOL INK cartridges. The screen displays
information such as instructions to insert and remove SOL INK cartridges. Follow these instructions to carry out the procedure.
After finishing washing, the sub power is automatically switched off.
You do not need to carry this out as part of your daily maintenance activities.

Draining Ink Remaining Inside the Machine

Procedure



Press

.

Press

several times.



Press

.

Press

twice.



Press

.

Press

.

Press

to execute.

Description

This removes ink inside the printer as a preliminary procedure for performing maintenance. The screen displays information
such as instructions to insert and remove cartridges. Follow these instructions to carry out the procedure. After finishing the
procedure, the sub power is automatically switched off.
You do not need to carry this out as part of your daily maintenance activities.

MENU

SUB MENU

SUB MENU

INK CONTROL

INK CONTROL

HEAD WASH

MENU

SUB MENU

SUB MENU

INK CONTROL

INK CONTROL

PUMP UP

«
...
118
119
120
121
122
...
»

Содержание LEC-300























































































































































Отзывы:

Нет отзывов

Похожие инструкции для LEC-300

imagePROGRAF BU-03

Бренд: Canon Страницы: 12

imagePROGRAF iPF6400SE

Бренд: Canon Страницы: 684

EV24 with SignMaster Pro

Бренд: Skycut Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды