Roland LEC-300 Скачать руководство пользователя

Страница: 135 / 150

133

Chapter 6 What to Do If

6-7 If a Message Appears

These are the main messages that appear on the

machine's display to prompt correct operation. They

do not indicate any error. Follow the prompts and take

action accordingly.

...]

Only a small amount of ink remains. Replace the cartridge indi-
cated by the flashing number with a new cartridge.

[PRESS POWER KEY TO CLEAN]

This appears when the machine has been unused for about
one month.
This feature is to remind you to switch on the sub power once
a month.



P. 74, "When Not in Use for a Prolonged Period"

[SET CARTRIDGE.]

Insert the ink cartridge indicated by the flashing number. This
message appears at times such as during ink cartridge replace-
ment.

[REMOVE CARTRIDGE.]

Remove the ink cartridge indicated by the flashing number.
This message appears at times such as during ink cartridge
replacement.

[SET CL-LIQUID]

Insert the SOL INK cleaning cartridge indicated by the flashing
number. This message appears at times such as during head
cleaning.

[REMOVE CL-LIQUID]

Remove the SOL INK cleaning cartridge indicated by the flash-
ing number. This message appears at times such as during head
cleaning.

[END OF THE SHEET]

The trailing edge of the media was detected during operation.
Press any button on the operation panel to clear the message.
Load new media.

[SHEET NOT LOADED PRESS SETUP KEY]

Load media and press

. This message appears when an

attempt to perform a printing test was made while no media
was loaded.

[INSTALL DRAIN BOTTLE]

Check whether the drain bottle is installed. Install the drain
bottle, then press

[CHECK DRAIN BOTTLE]

This appears when a certain amount of discharged fluid collects
in the drain bottle. To clear the message, press

. If this

screen appears, go to the [DRAIN BOTTLE] menu and discard the
discharged fluid in the bottle.



P. 54, "Disposing of Discharged Ink"

[CLOSE THE COVER (FRONT COVER, SIDE COVER

or MAINTENANCE COVER]

Close the front cover, side cover, maintenance cover. For safety,
the carriage does not operate while a cover is open.

[SET HEAD HEIGHT TO xxx]

The height of the print heads is lower than the height specified
on the computer.
The heads move to a location where you can operate the
height-adjustment lever. Adjust to the displayed height, then
press

[TIME FOR MAINTENANCE]

It is time to clean the heads using the cleaning kit. After verify-
ing, press



P. 59, "Cleaning Using the Cleaning Kit"

[TIME FOR WIPER REPLACE]

It is time to replace the wipers. After verifying, press



P. 65, "Replacing the Wipers"

[INK RENEWAL RECOMMENDED]

The white ink needs to be refreshed. After confirming, press



P. 72, "Maintenance Tasks for White Ink"

Содержание LEC-300























































































































































Результаты поиска

Содержание LEC-300

Отзывы:

Похожие инструкции для LEC-300

Бренды по названию

Популярные бренды

Roland LEC-300, Руководство пользователя

Результаты поиска

Содержание LEC-300

Отзывы:

Похожие инструкции для LEC-300

Бренды по названию

Популярные бренды