Roland LEC-300 Скачать руководство пользователя

Страница: 111 / 150

5-7 Performing Printing and Cutting Separately

109

Chapter 5 Feature Reference

From the test pattern, read the correction value at the location.

Enter the correction value you read.



Press



Press

Use

to set the correction value for [F] (the feed

direction).

Use

to set the correction value for [S] (the scanning

direction).

Press

to enable the setting.



Press

Check the results of adjustment.

Press

to execute.

If the printing and cutting lines are aligned, adjustment is complete.
If further adjustment is needed, go back to step

and fine-tune the adjustment.

Description

Depending on the composition of the media, the positioning of printing and cutting may be misaligned even when you're
using crop marks. Make corrections for misaligned printing and cutting for the media you're using.

Default Setting

[F] (feed direction): 0.00 mm
[S] (scanning direction): 0.00 mm

+2.0

-2.0

-1.0

+0.5

-0.5

+0.0

-0.0

+1.5

-1.5

+2.0

-2.0

+1.0

-1.0

+0.5

-0.5

+0.0

-0.0

+1.5

-1.5

FEED

SCAN

CROP - CUT ADJ.

SETTING

F :- 0.30 - 0.30mm

S : 0.00 - 0.20mm

CROP - CUT ADJ.

SETTING

CROP - CUT ADJ.

SETTING

Test pattern

Check the value on

the [SCAN] side.

Correction-value scale

Check the value on

the [FEED] side.

Cutting line

The point where the cutting line

intersects the correction-value

scale is the correction value. In this

figure, the value is "-0.3." Use the

same method to read the value on

the [FEED] side.

Cutting line

Scan direction

Printing position

Cutting position

Cutting position and print-

ing position are aligned.

Содержание LEC-300























































































































































Результаты поиска

Содержание LEC-300

Отзывы:

Похожие инструкции для LEC-300

Бренды по названию

Популярные бренды

Roland LEC-300, Руководство пользователя

Результаты поиска

Содержание LEC-300

Отзывы:

Похожие инструкции для LEC-300

Бренды по названию

Популярные бренды