51
Q&A
Overall / System
01
Does the sound change as on an analog
synthesizer according to temperature and the
passage of time?
Yes.
If the Aging function is “ON,” an internal temperature sensor is used
to apply change to some synthesizer sounds (sounds for which the
TONE parameter Pitch Drift is specified), simulating the way in which
temperature variation and the passage of time after startup can affect
the sound of an analog synthesizer.
Turn the Aging function “ON” as described below, and notice how the
sound changes.
1 .
Press the [MENU] (WRITE) button .
2 .
Use the [
Ç
SELECT
É
] knob to select “SYSTEM,” and
then press the [ENTER] (INIT) button .
3 .
Use the [
Ç
SELECT
É
] knob to select “Warm-up,” and
use the [- VALUE +] knob to select either “ON” or
“FAST .”
ON
Simulation is on. The status of Pitch Drift will change in approximately
ten minutes, and will subsequently stabilize at the value of the TONE
setting Pitch Drift.
FAST
This mode shortens the change of the ON setting to approximately
ten seconds, allowing you to hear the effect of Pitch Drift.
FIXED
The internal temperature is fixed at the value specified by Init Temp,
and the character of the sound at that point is maintained.
4 .
Hold down the [SHIFT] button and press the [MENU]
(WRITE) button to save the edited settings .
02
Can the internal speaker be turned off at all
times?
Yes.
Use the following procedure to turn the internal speaker “OFF.”
1 .
Press the [MENU] (WRITE) button .
2 .
Use the [
Ç
SELECT
É
] knob to select “SYSTEM,” and
then press the [ENTER] (INIT) button .
3 .
Use the [
Ç
SELECT
É
] knob to select “Speaker Sw,”
and use the [- VALUE +] knob to specify “OFF .”
4 .
Hold down the [SHIFT] button and press the [MENU]
(WRITE) button to save the edited settings .
03
Do the internal speakers produce enough
volume for a live performance?
They are not suitable for this purpose.
The internal speakers are intended for personal enjoyment by the
individual who is playing the instrument. For use in a live performance,
we recommend that you connect an external amp or speaker.
04
How do I save a sound that I created?
To completely save and reproduce the sound that you’re currently
hearing, you must save both the tones and the scene.
Save this data as follows.
Saving the tone
1 .
Select the edited tone, and press the [MENU] (WRITE)
button while holding down the [SHIFT] button .
2 .
Use the [
Ç
SELECT
É
] knob to select the part where
the tone you want to save is assigned, and then press
the [ENTER] (INIT) button .
3 .
Select the save-destination, and then press the
[ENTER] (INIT) button .
4 .
If you want to rename the tone that’s being saved,
use the [
Í
] [
Ë
] buttons to move the cursor and use
the [- VALUE +] knob to specify characters .
5 .
Press the [ENTER] (INIT) button .
A confirmation message appears.
If you decide to cancel, press the [EXIT] button.
6 .
To execute, press the [ENTER] (INIT) button .
Saving the scene
1 .
Select the edited scene, hold down the [SHIFT] button
and press the [MENU] (WRITE) button .
2 .
Use the [
Ç
SELECT
É
] knob to select “SCENE,” and
then press the [ENTER] (INIT) button .
3 .
Select the save-destination, and then press the
[ENTER] (INIT) button .
If you want to rename the scene that’s being saved, use the [
Í
]
[
Ë
] buttons to move the cursor and use the [- VALUE +] knob to
specify characters.
4 .
Press the [ENTER] (INIT) button .
A confirmation message appears.
If you decide to cancel, press the [EXIT] button.
5 .
To execute, press the [ENTER] (INIT) button .
05
Is this unit equipped with Bluetooth
functionality?
Yes, it is.
You can use its Bluetooth functionality in the following ways.
Bluetooth audio
Music played back from your mobile device can be mixed with
the sound of the internal sound engine, and output from this
unit.
* To adjust the playback volume, adjust the volume on your mobile device
or adjust the System setting “AuxIn/BT InLev.”
Bluetooth MIDI
You can also use apps with this instrument that are compatible
with Bluetooth MIDI (such as GarageBand).
