background image

 Pour utiliser en toute sécurité

10

ATTENTION

Brancher à une prise électrique conforme
aux caractéristiques de cet appareil (ten-
sion, fréquence et courant).

Une tension incorrecte ou un courant insuffisant
peuvent causer un incendie ou un choc
électrique.

Ne jamais utiliser à l'extérieur ni à un
endroit où l'appareil risque d'être exposé
à de l'eau ou à une humidité élevée. Ne
jamais toucher l'appareil avec des mains
mouillées.

Le non-respect de cette consigne risque de
provoquer un incendie ou un choc électrique.

Ne jamais insérer d'objet étranger dans
l'appareil. Ne jamais exposer l'appareil aux
déversements de liquides.

L'insertion d'objets comme des pièces de
monnaie ou des allumettes, ou le déversement
de liquides dans les orifices de ventilation
peuvent causer un incendie ou un choc
électrique. Si un objet ou du liquide s'infiltre dans
l'appareil, débrancher immédiatement le câble
d'alimentation et communiquer avec le
représentant Roland DG Corp. autorisé.

Ne jamais placer d'objet inflammable à
proximité de l'appareil. Ne jamais utiliser
de produit inflammable en aérosol à
proximité de l'appareil. Ne jamais utiliser
l'appareil dans un endroit où des gaz
peuvent s'accumuler.

Une combustion ou une explosion pourraient
se produire.

ATTENTION

Manipuler le câble d'alimentation, la fiche
et la prise électrique correctement et avec
soin.

Ne jamais utiliser un article endommagé, car cela
pourrait causer un incendie ou un choc
électrique.

Si une rallonge ou une bande
d'alimentation électrique sont utilisées,
s'assurer qu'elles correspondent aux
caractéristiques de l'appareil (tension,
fréquence et courant).

L'utilisation de plusieurs charges électriques sur
une prise unique ou une longue rallonge peut
causer un incendie.

Mise à la terre.

La mise à la terre peut prévenir un incendie ou
un choc électrique dus à une fuite de courant
en cas de défaillance.

Si l'appareil doit rester inutilisé pendant
une longue période, débrancher le câble
d'alimentation.

Cela peut prévenir les accidents en cas de fuite
de courant ou de démarrage accidentel.

Placer l'appareil de façon à ce que la fiche
soit facile d'accès en tout temps.

Ainsi, l'appareil pourra être débranché
rapidement en cas d'urgence. Installer l'appareil
près d'une prise électrique. En outre, prévoir
suffisamment d'espace pour que la prise
électrique soit facile d'accès.

S'il se produit des étincelles, de la fumée,
une odeur de brûlé, un bruit inhabituel ou
un fonctionnement anormal, débrancher
immédiatement le câble d'alimentation.
Ne jamais utiliser si un composant est
endommagé.

Continuer à utiliser l'appareil peut causer un
incendie, un choc électrique ou des blessures.
Communiquer avec le représentant Roland DG
Corp. Autorisé.

Caractéristiques

 Risque de décharge ou de choc électrique,

d'électrocution ou d'incendie

Содержание Camm-1 Pro GX-300





















































































Отзывы: