Rohde & Schwarz TS-PSU12 Скачать руководство пользователя страница 54

Страница: 54 / 62

Self-Test

R&S

TS-PSU12

User Manual 1504.4524.12 ─ 05

8 Self-Test

The Power Supply/Load Module 12V R&S TS-PSU12 has an integrated capability for
self-test. The following tests are implemented:

●

LED test

●

Power on test

●

TSVP self-test

8.1 LED Test

After power-on, all three LED's light up for around three seconds to indicate that the
5

V supply is present and all LED's are working. The following statements can be made

about the different LED states:

Table 8-1: Statements about the LED Test

LED

Description

One LED does not
light up

Hardware problem on the module

LED faulty

No LED's light up

No +5 V supply

8.2 Power on test

The power on test runs in parallel to the LED test. The following observations may be
made about the different display states of the LEDs:

Table 8-2: Observations about the power on test

LED

Description

PWR LED (green) on

All power supply voltages are present

PWR LED (green) off

At least one power supply voltage is missing

ERR LED (red) off

No error is present

ERR LED (red) Is lit or flashing

Hardware error is present (processor is not starting)

CH1 LED (yellow) off

No error is present

CH1 LED (yellow) flashing*

Channel has been deactivated because of an error
(the PSU-AC/DC converter is possibly not be turned
on).

CH2 LED (yellow) off

No error is present

CH2 LED (yellow) flashing*

Channel has been deactivated because of an error
(the PSU-AC/DC converter may not be turned on).

Power on test

Содержание TS-PSU12































































Результаты поиска

Содержание TS-PSU12

Отзывы:

Похожие инструкции для TS-PSU12

Бренды по названию

Популярные бренды

Rohde & Schwarz TS-PSU12, Руководство пользователя

Результаты поиска

Содержание TS-PSU12

Отзывы:

Похожие инструкции для TS-PSU12

Бренды по названию

Популярные бренды