manualshive.com logo in svg

Rohde & Schwarz TS-PSU12, Руководство пользователя, Страница: 38 / 62

Поделиться
Скачать
Rohde & Schwarz TS-PSU12 Скачать руководство пользователя страница 38

Function Description

R&S

®

TS-PSU12

22

User Manual 1504.4524.12 ─ 05

5.3.3 Monitor output

The R&S TS-PSU12 has two pins on the X10 front connector that pass the input volt-
age of the ADC to the output through a buffer. In this way, the selected measurement
source can be recorded using an external oscilloscope or digitizer. The voltages and
value range on these monitor outputs (CHx_MHI and CHx_MLO) are as follow:

Table 5-1: Voltages and value range of monitor outputs

Selected source

Source signal for 2.50V

full scale of monitor voltage

Conversion factor

Force voltage

52.7 V

Source signal in V = 21.08 * moni-
tor voltage in V

Sense voltage

52.7 V

Source signal in V = 21.08 * moni-
tor voltage in V

Current 10 mA

12,4 mA

Source current in mA = 4,97 *
monitor voltage in V

Current 100 mA

110 mA

Source current in mA = 43,9 *
monitor voltage in V

Current 500 mA

932 mA

Source current in A = 0,373 *
monitor voltage in V

The monitor output signal must be measured differentially at high impedance. 10 k

Ω

 is

built in internally before CHx_MHI and CHx_MLO each as a protective mechanism
against short-circuits.

Signals CHx_MHI / CHx_MLO must be measured floating against the force or sense
potential. Depending on the quadrant of the source, the potential against CHx_MLO
approximates CHx_LO (output voltage positive) or CHx_HI (output voltage negative).
This means the common mode voltage on CHx_MLO against CHx_LO is approxi-
mately 0 V to approximately -12 V.

5.4 Relay matrix

The relay matrix implemented in the Power Supply/Load Module 12V R&S TS-PSU12
is used for flexible connection and simple wiring of test objects. Its layout is as follows:

 

 

Relay matrix

Содержание TS-PSU12































































Отзывы:

Нет отзывов