manualshive.com logo in svg

Rohde & Schwarz TS-PSU12, Руководство пользователя, Страница: 40 / 62

Поделиться
Скачать
Rohde & Schwarz TS-PSU12 Скачать руководство пользователя страница 40

Function Description

R&S

®

TS-PSU12

24

User Manual 1504.4524.12 ─ 05

To prevent the relay contacts from being destroyed, the relays should only be switched
if no current is flowing through them. Before a contact is activated, the channel should
be turned off electronically.

The following functions are available to operate these relays:

●

rspsu_Connect

●

rspsu_Disconnect

●

rspsu_DisconnectAll

The function 

rspsu_DisconnectAll

 can be used to break all connections that were

set up with 

rspsu_Connect

. 

rspsu_DisconnectAll

 has no effect on the configu-

ration of the coupling relays or ground relay.

5.4.2 Coupling Relays

The coupling relays connect the local analog bus on the module with the analog bus in
the R&S CompactTSVP. The function 

rspsu_ConfigureCoupling

 defines the sta-

tus of the coupling relays. Please consider that the function 

rspsu_DisconnectAll

does not open these relays.

5.4.3 Ground relays

Each channel of the R&S TS-PSU12 has its own ground relay that can be used to con-
nect the CHx_LO signal to ground. PSU channels are operated ground free in their
basic state. The function 

rspsu_ConfigureGround

 is used to determine whether a

channel is being operated with ground reference or ground free. Also note that

rspsu_DisconnectAll

 does not affect the ground relay!

For technical reasons, a non-switched PSU channel (all matrix and front relays of a
channel are opened) is automatically grounded with the ground relay. It is automati-
cally opened again before another connection is made if the channel is configured
ground-free.

5.5 Trigger unit

5.5.1 Trigger outputs

The Power Supply/Load Module 12V R&S TS-PSU12 can generate trigger signals on
lines PXI_TRIGn (X20) and XTOn (X10). The polarity of the trigger signal can be
adjusted. The following events may cause a change in the level on trigger lines:

●

Call to function 

rspsu_InitiateTrigger

. This function generates a “General

Purpose” trigger (trigger pulse approximately 1 μs long) if trigger source “GP” has

 

 

 

 

Trigger unit

Содержание TS-PSU12































































Отзывы:

Нет отзывов