manualshive.com logo in svg

Rohde & Schwarz TS-PSU12, Руководство пользователя, Страница: 28 / 62

Поделиться
Скачать
Rohde & Schwarz TS-PSU12 Скачать руководство пользователя страница 28

Layout

R&S

®

TS-PSU12

12

User Manual 1504.4524.12 ─ 05

LED

Description

CH1

(yellow)

Continuously lit:

Channel 1 is working with constant current

Flashing:

The protective mechanism for Channel 1 has engaged (see also 

Chapter 5.2.8, "Protec-

tive mechanisms"

, 

on page 20)

CH2

(yellow)

Continuously lit:

Channel 2 is working with constant current

Flashing:

The protective mechanism for Channel 2 has engaged (see also 

Chapter 5.2.8, "Protec-

tive mechanisms"

, 

on page 20)

4.3 Mechanical Layout R&S TS-PDC

The R&S TS-PDC module is a rear I/O module for mounting in the back of the R&S
CompactTSVP. The board height of the module is 3 HU (134 mm). The module is
secured in place with the two retaining screws on the front panel. Connector X20 con-
nects the R&S TS-PDC module to the extension backplane in the R&S CompactTSVP.
The R&S TS-PDC module must always use the corresponding rear I/O slot for the
main module.

The R&S TS-PDC module must always be inserted in the corresponding rear I/O slot
of the R&S TS-PSU12 module.
If modules are inserted incorrectly (e.g. cPCI/PXI standard modules in the front), both
modules may be damaged irreparably.

 

Mechanical Layout R&S TS-PDC

Содержание TS-PSU12































































Отзывы:

Нет отзывов