background image

RFT1000 in RACS 5 User Manual.doc

 

2017-10-05 

 

 

13/13 

 

5.

 

O

RDERING INFORMATION

 

Table 7 Ordering information 

Product 

Description 

RFT1000 

Fingerprint and Mifare Ultralight/Classic proximity card reader. 

MFC-2 

13.56 MHz Mifare Classic ISO size thin PVC card, 1k bytes memory. 

MFC-3 

13.56 MHz Mifare Classic ISO size thin PVC card, 4k bytes memory. 

6.

 

P

RODUCT HISTORY

 

Table 8 Product history 

Product version 

Released 

Description 

1.0 

06/2013 

The first commercial version of the product 

1.1 

12/2013 

Built-in antenna modifications 

 

 
 
 

 

This symbol placed on a product or packaging indicates that the 
product should not be disposed of with other wastes as this may 

have a negative impact on the environment and health. The user 
is obliged to deliver equipment to the designated collection points 
of  electric  and  electronic  waste.  For  detailed  information  on 

recycling, contact your  local authorities, waste disposal company 
or point of purchase. Separate collection and recycling of this type 

of  waste  contributes  to  the  protection  of  the  natural  resources 
and  is  safe  to  health  and  the  environment.  Weight  of  the 
equipment is specified in the document. 

 
 

 
 

 
 

Contact: 

Roger sp. z o.o. sp.k. 

82-400 Sztum 

Gościszewo 59 

Tel.: +48 55 272 0132 
Fax: +48 55 272 0133 

Tech. support: +48 55 267 0126 

E-mail: 

[email protected]

 

Web

www.roger.pl

 

 

Содержание RFT1000














Отзывы: