background image

PR611 and PR621 Installation guide Rev.B EN 

2009-11-06 

 

 
Page 

10

 of 

13

 

 

Ordering Information 

PR611 

PR611 controller, standard version, connection via pig tail cable 

PR621 

PR621 controller, standard version, connection via screw terminals 

RM-2 

Module consisting of two relay outputs rated 1.5A/24V each with one switched 

contact NO/NC. Relay contacts are protected against overvoltages using metal-
oxide varistors (MOVs).  Relays can be triggered by applying low as well as 

high triggering signal. Triggering of relay is indicated by LED on the module’s 
board. 

RM-2 PCB 

RM-2 PCB module without enclosure 

XM-2 

Input/output addressable extension module provides two input lines NO/NC 
and two relay outputs with one switched contact NO/NC rated 1.5A/24V. Relay 
contacts are protected against overvoltages using metal-oxide varistors 

(MOVs).  Triggering of each relay is indicated by a LED installed on the 
module’s board. Communication with parent device can be performed using 

CLK/DTA lines. The module can be located in a distance of 150 m from the host 
device (controller). 

XM-2 PCB 

XM-2 PCB module without enclosure 

UT-2 

RS232-RS485 communication interface 

UT-2USB 

USB-RS485 communication interface 

RUD-1 

USB-RS485 communication interface with 12V DC/150mA supply output 

UT-4 Ethernet-RS485/RS232 

communication 

interface 

 

Contact 

Roger sp. j. 

82-416 Go

ś

ciszewo 

Go

ś

ciszewo 59 

Tel.:  +48 55 272 01 32 

Fax: +48 55 272 01 33 

Technical support PSTN: +48 55 267 01 26  

Technical support GSM +48 664 294 087  

e-mail: 

[email protected]

 

 

 

Such symbol on the product or its package means that the 
product should not be disposed together with other wastes, 

because it may cause negative effects to  environment and 
humans health. User is responsible for delivering used equipment 
to the allotted locations for gathering used electrical and 

electronic devices. Detailed information on recycling can be found 
at relevant local authorities, in a disposing company or in a place, 

where the product was bought. Separate gathering and recycling 
of such wastes contributes to natural resources protection and is 

safe for humans health and for natural environment. The 
equipment’s weight is shown in the guide. 

Содержание PR611














Отзывы: