Roger MCT88M-IO Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

Roger MCT88M-IO Скачать руководство пользователя страница 5

MCT88M-IO Operating Manual.doc

2019-03-06

5/20

Fig. 4 LED indicators and function keys

LED indicators

The terminal is equipped with three LED indicators (fig. 4) which are used to signal integral functions and
they can be additionally programmed with other available functions within high level configuration (VISO).

Table 2. LED indicators

Indicator

Colour

Integral functions

LED STATUS

Red/green

Default indicator colour is red. If the terminal is assigned to Alarm
Zone then the LED indicates zone arming (red) or disarming (green).

LED OPEN

Green

LED indicates access granting.

LED SYSTEM

Orange

LED indicates card reading and can signal other system functions
including device malfunction.

Note: Synchronic pulsing of all three LEDs signifies lost communication with MC16 controller.

Buzzer

The terminal is equipped with buzzer which is used to signal integral functions and it can be additionally
programmed with other available functions within high level configuration (VISO).

Inputs

The  terminal  offers  3  general  purpose  parametric  inputs  type  NO/NC/EOL/DW  and  1  input  internally
connected  to  tamper  contact.  Input  types  and  electric  parameters  such  as  response  time  and  parametric
resistors  are  defined  within  low  level  configuration  (RogerVDM).  Input  functions  are  assigned  within  high
level configuration (VISO). Multiple functions can be assigned to the same input at the same time.

«
...
3
4
5
6
7
...
»

Содержание MCT88M-IO





















Отзывы:

Нет отзывов