background image

MCT88M-IO Operating Manual.doc 

  

2019-03-06 

 

4/20 

 

Ethernet interface 

MCT88M-IO terminal can communicate with MC16 controller via LAN if MCX16-RS expander is connected 
as intermediary device (fig. 3). In such scenario, MC16 controller and MCX16-RS can be connected to the 
same network but they communicate solely via RS485 bus. 
Alternatively,  the  Ethernet  interface  can  be  used  for  communication  of  the  terminal  with  virtual  controller 
which  operates  as  Windows  Service  on  a  computer  in  LAN.  Virtual  controller  enables  the  operation  of 
MCT88M-IO  as  PoS  terminal  or  assets  management  terminal.  Virtual  controller  is  a  component  of 
RogerSVC software package which is available at 

www.roger.pl

. 

 

 

Fig. 3 Connection of the terminal to MC16 controller via MCX16-RS expander 

Keypad 

The  terminal  is  equipped  with  numeric  touch  keypad  and  backlight.  The  keypad  can  be  used  for  user 
identification with PIN and for various keypad commands. By default, the key # is used for PIN confirming. 

Function keys 

The terminal is equipped  with four  touch function keys (fig. 4). Various functions  can be assigned to  these 
keys within high level configuration (VISO) e.g. Set T&A Mode, Register Guard Tour Event, Set Automation 
Node On, etc. Within low  level configuration (RogerVDM) of the terminal it  is possible configure  if terminal 
distinguishes  short  and  long  key  pressings.  Consequently  each  types  of  key  press  can  be  assigned  with 
different function. 

Display 

The terminal is equipped with colour display (4 lines, 16 characters each). The display can be configured in 
regard of background and font colours within low level configuration (RogerVDM) and in regard of displayed 
information within high level configuration by means of 

Display

 command in VISO software navigation tree. 

Moreover,  default  functions  key  icons,  splash  screen  and  screensaver  can  be  replaced  using  device 
memory  card.  Four  new  icons  can  be  copied  to ICONS  folder  on  memory  card  (fig. 15)  and  they  must  be 
named as icon_001.bmp, icon_002.bmp, icon_003.bmp and icon_004.bmp. Splash screen file in the same 
folder must be named as icon_000.bmp. Screensaver graphics must be named as scrnsvr.bmp and it must 
be  copied  to  the  main  folder  of  memory  card  instead  of  ICONS  folder.  Icon  files  must  in  bmp  format, 
60x60pixels  dimensions  and  with  24bit  colour  depth.  Splash  screen  and  screensaver  pictures  must  be  in 
bmp format, 320x240pixels dimensions and 24bit colour depth. 
 

Содержание MCT88M-IO





















Отзывы: