manualshive.com logo in svg

Roger MCT88M-IO, Руководство по эксплуатации, Страница: 14 / 20

Поделиться
Скачать
Roger MCT88M-IO Скачать руководство пользователя страница 14

MCT88M-IO Operating Manual.doc 

  

2019-03-06 

 

14/20 

 

Default gateway 

Gateway IP address. 

UDP port 

UDP port 

Ethernet encryption key 

Parameter  defines  key  for  encryption  of  communication  in  Ethernet 
(LAN). Range: 1-16 ASCII characters. 

RS485 address 

Parameter  defines  device  address  on  RS485  bus.  Range:  100-115. 
Default value: 100. 

RS485 communication timeout [s]  Parameter  defines  delay  after  which  device  will  signal  lost 

communication  with  controller.  When  set  to  0  then  signaling  is 
disabled. Range: 0-64s. Default value: 20s. 

RS485 encryption 

Parameter enables encryption at RS485 bus. Range: [0]: No, [1]: Yes. 
Default value: [0]: No. 

RS485 encryption key 

Parameter defines key for encryption of communication at RS485 bus. 
Range: 4-16 ASCII characters. 

NFC/BLE  authentication  factor 
encryption key 

Parameter  defines  encryption  key  for  NFC/BLE  key  (authentication 
factor). Range: 4-16 ASCII characters. 

NFC/BLE 

communication 

encryption key 

Parameter  defines  key  for  encryption  of  NFC/BLE  communication. 
Range: 4-16 ASCII characters. 

BLE authentication factor class 

Parameter  defines  acceptable  type  of  keys  (authentication  factors) 
created  in  Roger Mobile  Key  app for Bluetooth (BLE) communication. 
UCE means lower security and quicker identification while REK means 
higher  security  and  slower  identification.  It  is  necessary  to  apply 
classes  in  RMK  which  are  acceptable  for  terminal.  Range:  [1]:  REK, 
[2]: UCE, [3]: UCE + REK. Default value: [3]: UCE + REK. 

Optical signalisation 

LED  SYSTEM  pulsing  when  card 
near reader 

Parameter enables LED SYSTEM (orange) pulsing when card is close 
to the device. Range: [0]: No, [1]: Yes. Default value: [0]: No. 

Backlight level [%] 

Parameter  defines  backlight  level.  When  set  to  0  then  backlight  is 
disabled. Range: 0-100. Default value: 100. 

Backlight dimming when card/key 
used 

Parameter  enables  temporary  backlight  dimming  whenever  card  is 
read or key is pressed. Range: [0]: No, [1]: Yes. Default value: [0]: No. 

LED  SYSTEM  flash  after  card 
read 

Parameter enables short flash of LED SYSTEM (orange) when card is 
read. Range: [0]: No, [1]: Yes. Default value: [0]: Yes. 

LED  SYSTEM  flash  after  key 
press 

Parameter enables short flash of LED SYSTEM (orange) when key  is 
pressed. Range: [0]: No, [1]: Yes. Default value: [0]: Yes. 

Acoustic signalisation 

Buzzer loudness level [%] 

Parameter defines buzzer loudness level. When set to 0 then buzzer is 
disabled Range: 0-100. Default value: 100. 

Short sound after card read 

Parameter  enables  short  sound  (beep)  generating  by  buzzer  when 
card is read. Range: [0]: No, [1]: Yes. Default value: [0]: Yes. 

Short sound after key press 

Parameter enables short sound (beep) generating by buzzer when key 
is pressed. Range: [0]: No, [1]: Yes. Default value: [0]: Yes. 

Keypad settings 

Keypad activated 

Parameter  enables  deactivation  of  keypad.  Range:  [0]:  No,  [1]:  Yes. 
Default value: [0]: Yes.

 

Time between keys in PIN [s] 

Parameter defines max. time between two consecutive key pressings. 
Range: 0-64. Default value: 10. 

Single key press 

Parameter  enables  separate  transmission  of  each  pressed  key  to 

Содержание MCT88M-IO





















Отзывы:

Нет отзывов