background image

MCT88M-IO Operating Manual.doc 

  

2019-03-06 

 

16/20 

 

Tamper, Alarm A, Alarm B [Ohm] 

Parameter defines resistor for parametric (EOL) inputs. 

Output polarity 

OUT1, OUT2, REL1 

Parameter  defines  polarity  of  output.  Normal  polarity  means  that  the 
output  by  default  is  switched  off  while  Reversed  polarity  means  that 
the  output  by  default  is  switched  on.  Range:  [0]:  Normal  polarity,  [1]: 
Reversed polarity. Default value: [0]: Normal polarity. 

Display 

Default background colour 

Parameter defines default colour of font background. 

Default font colour 

Parameter defines default colour of fonts. 

Default font background colour 

Parameter defines default colour of font background. 

File 

name 

with 

additional 

characters 

File name with additional characters. 

Screensaver 

Parameter  enables  screensaver  displaying.  Range:  [0]:  No,  [1]:  Yes. 
Default value: [0]: Yes. 

Screensaver display delay [s] 

Parameter  defines  inactivity  time  before  screensaver  displaying. 
Range: 0-3600. Default value: 60. 

Comments 

DEV, KBD1, CDI1, IN1, IN2, IN3, 
IN4  (Tamper),  OUT1,  OUT2, 
REL1,  

Parameter  defines  any  text  or  comment  which  corresponds  to  the 
object. It is later displayed in VISO program. 

Serial card number (CSN) settings 

Serial number length (CSNL) [B] 

Parameter defines the number of bytes from serial card number (CSN) 
which  will  be  used  to  generate  returned  card  number  (RCN).  RCN  is 
the  actual  card  number  read  by  reader  and  it  is  created  as  sum  of 
serial card number (CSN) and programmable card number (PCN). 

Programmable card number (PCN) settings for Mifare Ultralight 

Sector type 

Parameter  defines  sector  type  with  programmable  number  (PCN).  If 
the  option  [0]:None  is  selected  then  card  returned  number  (RCN)  will 
include  only  CSN  and  PCN  will  be  discarded.  Range:  [0]:  None,  [1]: 
SSN. Default value: [0]: None. 

SSN first page number 

Parameter  defines  location  of  SSN  in  card  memory.  Range:  4-12. 
Default value: 4. 

Programmable card number (PCN) settings for Mifare Classic 

Sector type 

Parameter  defines  sector  type  with  programmable  number  (PCN).  If 
the  option  [0]:None  is  selected  then  card  returned  number  (RCN)  will 
include  only  CSN  and  PCN  will  be  discarded.  Range:  [0]:  None,  [1]: 
SSN, [2]: MAD. Default value: [0]: None. 

Format 

Parameter  defines  format  of  PCN.  Range:  [0]:  BIN,  [1]:  ASCII  HEX. 
Default value: [0]: BIN. 

First byte position (FBP) 

Parameter  defines  the  position  of  the  first  byte  for  PCN  in  data  block 
on card. Range: 0-15. Default value: 0. 

Last byte position (LBP) 

Parameter  defines  the  position  of  the  last  byte  for  PCN  in  data  block 
on card. Range: 0-15. Default value: 7. 

Sector ID 

Parameter defines sector number where PCN  is stored. Range: 0-39. 
Default value: 1. 

Application ID (AID) 

Parameter defines application ID number (AID) which indicates sector 
where PCN number is stored. Range: 0-9999. Default value: 5156. 

Содержание MCT88M-IO





















Отзывы: